







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Toto Bathroom Remodeling: The Denton Owner’s Guide
Toto bathroom remodeling in Denton runs $9,000 to $28,000 for a full bathroom, and most Toto fixture replacements and finish upgrades can be scheduled within the same week. The price depends on how much of the room we touch: a fixture and finish update sits at the low end, a full gut with a new subfloor, tile, and vanity lands at the top. We’re an independent remodeling contractor in Denton, not affiliated with Toto, and we work with the brand’s spec sheets on hand.

Most Denton owners find us the same way. The bidet seat stops heating, or the fill valve runs long after the tank should be full, or the finish on a 15-year-old Toto toilet has worn through at the rim. They’ve priced the part, and then they start asking the bigger question: is it worth fixing this fixture, or is it time to redo the whole bathroom around it? That’s the conversation this page is built for.
Key Takeaways
- Toto bathroom remodeling in Denton runs $9,000 – $28,000, with fixture-only and finish work at the lower end.
- Toto’s washlet seats, fill valves, and flush towers are model-specific – the part number on the box matters more than the brand name on the lid.
- We’re an independent contractor, not a Toto dealer or affiliate. We match the part to the model and install it to spec.
- Every project carries the 365-Day Done Right Promise: if it fails inside a year, we come back and correct it at no charge.
Which Toto Models This Applies To

Toto’s residential line splits into a few families, and the part that fits one generally won’t fit another. The Drake and Eco Drake (CST743, CST744) use a fill valve and flapper setup that’s been stable for years, so parts are easy to source. The Ultramax II and Vespin II are one-piece units with a different flush tower. The Aquia and Carlyle use a dual-flush fill valve. And the washlet seats (S550e, C5, K300) each have their own control board, remote, and water heater assembly.
Before you buy anything, find the model number. It’s stamped on the inside of the tank lid on most Toto toilets, and on a label under the seat on washlets. Write it down exactly, including any suffix. A missing suffix is the most common reason a $40 part turns into a $40 return.
Then decide OEM versus aftermarket. For Toto fill valves and flappers, OEM is worth the extra $10 to $20: the tolerances on the Aquia dual-flush valve in particular are tight enough that aftermarket copies run long or short. For washlet seats, the control board and heater are Toto-only. For finish work and the surrounding bathroom, we install KartMaid vanities and Cambria and Silestone surfaces alongside Toto fixtures when a Denton owner wants the room to feel of a piece.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Toto Bathroom Remodeling Is Failing
The failure modes depend on which part you own. These are the ones we see most in Denton bathrooms.
- The toilet runs for 20 – 30 seconds after a flush. That’s a fill valve that isn’t seating, or a flapper that’s curled at the edge. Both are cheap parts, and both waste water on every flush. In a Denton summer, when the water bill climbs, this gets expensive fast.
- The washlet seat won’t heat, or heats unevenly. The water heater element inside the seat has failed, or the control board isn’t sending current to it. A seat that’s warm on one side only points to the heater, not the board.
- Water pooling at the base of the toilet. The wax ring has failed, or the flange is cracked. That’s a pull-the-toilet job. Left alone, water finds the subfloor and the ceiling below.
- The flush is weak, or you have to hold the handle. The flush tower or the rim jets are scaled up. Denton’s water runs hard, and scale builds inside the rim on Toto one-piece units after seven to ten years without a descale.
- The seat finish is worn or crazed at the rim. Not a failure, but a sign the fixture has lived its service life. Toto’s vitreous china holds up well, but the glaze on a 1990s model will show its age.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a Denton owner, the honest range depends on what’s being replaced. Here’s how the numbers break down when we do the work.
| Scope | Installed price range |
|---|---|
| Full bathroom remodel (Toto fixtures, tile, vanity, subfloor) | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Bathroom vanity installation | $800 – $3,000 |
The range moves with three things: how much of the room gets demoed, whether the subfloor or rough-in needs correction, and the level of tile and fixture spec. We put a written price in front of you before any work starts. No numbers that move at the door. And every completed project carries the 365-Day Done Right Promise: if it fails inside a year, we return and correct it at no charge.
DIY or Call Us?
Some of this you can check yourself. Pull the tank lid, confirm the model number, and look at the flapper. If it’s curled or stiff, a replacement flapper is a five-minute job with a screwdriver. A washlet seat that’s still heating but leaking from the wand can sometimes be fixed with a new wand seal.
Where DIY goes wrong: pulling a toilet to replace a wax ring without checking the flange, changing a fill valve and cross-threading the shank, or replacing a washlet control board and finding the heater was the real problem. Any work on the toilet’s water supply or drain connection is also where a small leak turns into an $1,800 subfloor repair. If you’re not sure which part failed, that’s the moment to call. Our technicians have up to 22 years of experience, and we’ll tell you straight whether the part is worth replacing or the fixture has earned its retirement.
Call (844) 651-3175 for a free estimate. A live person picks up, any hour.
FAQs

Seven to ten years is typical in Denton, closer to seven on the hard-water side of town. The rubber in the flapper hardens faster here than in softer-water climates, and the fill valve seals wear at the same rate. If your toilet is past the ten-year mark and running long after a flush, the part has lived its life. Call (844) 651-3175 for an exact quote – estimates are free.
Sometimes. A fill valve can be descaled and re-seated; a washlet wand leak can often be fixed with a new seal. But a cracked flush tower or a failed heater on a washlet seat usually isn’t repairable, and the part replacement costs less than the labor to chase a fix. We’ll tell you which one you’re looking at before we quote. Call (844) 651-3175 to schedule a free estimate.
A fill valve or flapper is a 30-minute service call. A wax ring and flange correction takes one to two hours. A washlet seat swap is 45 minutes. A full bathroom remodel, which is where the Toto fixtures usually get replaced alongside the tile and vanity, runs one to three weeks. Call (844) 651-3175 for a written scope and timeline.
We match the model number and suffix on the tank lid to Toto’s current parts list, then source OEM where it matters (fill valves, flappers, control boards) and a quality aftermarket equivalent where it doesn’t (supply lines, seat bolts). You get the part number on the written quote, so you can verify the match before we install. Call (844) 651-3175 for a free estimate.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












