







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Denton Owner’s Guide
For a home addition or ADU in Denton built with Schluter waterproofing and uncoupling systems, plan on $45,000 – $130,000 for the addition itself and $90,000 – $220,000 for a full ADU, depending on square footage, foundation type, and finish level. The Schluter component we’re talking about here is the waterproofing membrane, uncoupling mat, or bonded flange that ties tile and wet areas to the rest of the build, and it typically runs a small fraction of the total budget while causing the most expensive failures when it’s installed wrong.

Owners usually find out something is off the same way: a soft spot or a dark ring at the floor line in a new bathroom or kitchenette, grout cracking in a straight line across a slab, or a musty smell in a finished room that didn’t smell that way six months ago. In Denton, where the black clay soil moves with every wet and dry cycle, those symptoms show up faster than they do on stable ground. Call (844) 651-3175 and a live person picks up, day or night.
Key Takeaways
- Schluter failures in Denton additions are usually installation or substrate problems, not product defects.
- Expect $45,000 – $130,000 for a home addition, $90,000 – $220,000 for an ADU, and $30,000 – $80,000 for a garage conversion.
- You get a written price before any work starts, and the 365-Day Done Right Promise covers the finished work for a full year.
Which Schluter Models This Applies To

Schluter’s wet-area and floor systems are sold by series, and the series is what determines which membrane, flange, and trim pieces match what’s already in your addition. The names you’ll see on the box or the cut edge of the mat are DITRA (the uncoupling membrane for tile over slab or plywood), DITRA-HEAT (the same mat with heat cable clips molded in), KERDI (the sheet waterproofing for showers and wet walls), KERDI-BOARD (the foam backer board), KERDI-LINE and KERDI-DRAIN (linear and point drains with bonded flanges), and DITRA-SOUND for acoustic separation. Each has its own thickness and its own matching drain or trim profile, and they don’t cross over.
To identify what you have, read the printing on the exposed edge of the mat – DITRA is typically 1/8 in thick with a square-grid fleece backing, while KERDI shows its printed logo along the sheet. Measure the drain flange opening before you order anything; KERDI-DRAIN flanges are sized to specific drain bodies and a mismatched flange is one of the most common returns we see on Denton jobs. Then decide OEM versus aftermarket: Schluter’s own replacement rolls and flanges are the safe match because the system’s warranty depends on using matched components. Generic uncoupling mats are cheaper, but they won’t carry the same manufacturer backing, and on an addition where you’re already spending five figures, that’s a poor trade.
Bradford Remodeling Co Denton is an independent remodeling contractor. We’re not affiliated with Schluter, and we don’t stock or carry parts on a truck – we source what your project needs by model and spec.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
- Grout cracking in a straight line. That’s usually the uncoupling mat not doing its job over a moving slab, which is common in Denton’s clay soil. The tile is fine; the layer under it isn’t isolating movement.
- Soft or hollow-sounding tile near a drain. Water has gotten under the membrane, often from a flange that wasn’t bonded correctly or a seam that was lapped the wrong direction. By the time you hear the hollow tap, the substrate is wet.
- Musty smell in a finished bathroom or kitchenette. Trapped moisture behind KERDI or KERDI-BOARD with a compromised seam. Denton’s summer humidity makes this show up in weeks, not months.
- Lifted or peeling membrane edge at a wall or curb. Usually a thin-set compatibility problem – the wrong mortar was used under the membrane, so it never bonded. The product was right; the install wasn’t.
- Efflorescence or white crust on grout lines. Moisture is migrating through the assembly, which points to a missing or incomplete waterproofing layer. In a home addition, that often traces back to a transition where the new wet area meets the existing house.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

When the problem is the Schluter assembly in a home addition or ADU, the honest cost is the cost of opening, correcting, and re-finishing the affected area – and that number depends on the scope of the addition. For scheduling purposes, here’s where Denton projects land:
| Project | Installed Price Range |
|---|---|
| Home Addition | $45,000 – $130,000 |
| ADU Construction | $90,000 – $220,000 |
| Garage Conversion | $30,000 – $80,000 |
| Walk-In Shower Installation (Schluter wet area) | $4,500 – $12,000 |
| Bathroom Remodel | $9,000 – $28,000 |
What moves the range: square footage, foundation work, whether the affected Schluter area is a small wet zone or the full footprint, and finish level. What doesn’t move: our price. You get it in writing before any work starts, and it doesn’t change at the door. Every completed project carries the 365-Day Done Right Promise – if the work fails within that year, we come back and correct it at no charge. Free estimates, live-person phone coverage around the clock.
DIY or Call Us?
You can safely check a few things yourself: read the series name off the mat edge, measure the drain flange, look for lifted seams, and note where the tile sounds hollow with a light tap. What you shouldn’t do is pull up membrane or re-bond a flange on a finished assembly – a bad DIY patch usually traps more water than it stops and turns a small correction into a full tear-out. On a slab addition in Denton, the substrate also has to be checked for moisture and flatness before anything goes back down, and that’s a measurement job, not a guess.
The safest split is: inspect and document, then let a crew do the correction. Call (844) 651-3175 for a free estimate – we’ll tell you what’s actually failed and what it costs to fix, in writing, before we touch anything.
FAQs

How long does a Schluter membrane last in a Denton home addition?
Installed correctly, a Schluter uncoupling or waterproofing system is built to last the life of the tile assembly – decades, not years. What fails early is installation: wrong thin-set, unsealed seams, or a flange that never bonded. On Denton’s clay, the substrate prep matters as much as the product. Call (844) 651-3175 for an exact quote on your situation – estimates are free.
Can it be repaired instead of replaced?
Sometimes yes – a single lifted seam or a localized wet spot can often be corrected without tearing out the whole floor or shower. It depends on how far water traveled and whether the substrate is sound. We’ll tell you plainly which one you’re looking at. Call (844) 651-3175 for a free estimate.
How long does the swap take?
A localized membrane correction is usually a few days once materials are on site; a full wet-area redo or a portion of an addition runs one to three weeks. On new additions and ADUs, the Schluter work is sequenced into the build schedule, not squeezed in. You’ll see the timeline in your written scope. Call (844) 651-3175 to schedule your free estimate.
How do you source the part?
We match the exact Schluter series, thickness, and flange size your assembly requires and source it by model and spec – we don’t guess at a substitute. Bradford Remodeling Co Denton is independent and not affiliated with Schluter, so we buy what the spec calls for. Our technicians have up to 22 years of experience, and we also work with KraftMaid, Cambria, and Silestone on the finishes side. Call (844) 651-3175 and a live person will walk you through it.
Whether your addition needs a targeted Schluter correction or a full re-build of a wet area, the next step is a free estimate with a written price before any work starts. Call Bradford Remodeling Co Denton at (844) 651-3175 – a real person answers, any hour, and we’ll tell you exactly what’s failing and what it costs to make it right.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












