







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Atlas Kitchen Remodeling: The Denton Owner’s Guide
Kitchen remodeling built around Atlas cabinetry and components in Denton typically runs $14,000 – $45,000 installed, with cabinet installation alone at $4,000 – $13,000. If a door has delaminated, a drawer box has split at the staple line, or a cabinet run is sagging off the wall in a house off Scripture Street or near the Square, you’re most likely dealing with a failed component rather than the whole kitchen. Most owners find out the hard way: a soft spot under the sink, a door that won’t sit flush in summer, or a hinge plate that pulls clean out of the stile.

Which Atlas Models This Applies To

Atlas has been sold through builder channels and cabinet distributors around North Texas for decades, and the parts don’t cross series. A door from a flat-slab frameless line won’t fit a face-frame box, and the hinge bore pattern changed across production runs. Before you order anything, pull the sticker from inside a cabinet door or on the back of a drawer box; it carries the series and finish code. Failing that, measure the overlay (the amount the door covers the face frame), the door thickness, and the hinge cup bore, which is almost always 35mm but not always centered.
On the OEM-versus-aftermarket question: Atlas-branded replacement doors are the safe match for color and profile, but quality aftermarket boxes, drawer slides, and hinges often beat the original hardware for daily use. Soft-close undermount slides and adjustable European hinges from makers like Blum and Grass cost less than an OEM swap and outlast the originals. We’re an independent Denton service provider and not affiliated with Atlas, so we quote both paths with a written price before any work starts and let the spec sheet decide.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Atlas Kitchen Remodeling Is Failing
- Doors that swell and stick in summer. North Texas humidity swings push moisture into particleboard cores, and the door grows. If it only sticks June through September, the core is absorbing water.
- A drawer bottom sagging under weight. The bottom panel is thin hardboard stapled into a groove, and staples pull out when the box is overloaded. A sagging drawer usually needs a new box, not a new slide.
- Hinges pulling out of the stile. Screw holes strip in MDF and particleboard. If two or more hinges on the same run are loose, the cabinet face is taking stress the frame wasn’t built to carry.
- Delamination at the door edge. Thermofoil and laminate skins lift at the edges first, usually above the dishwasher or near the range where heat and steam hit hardest. Once the edge lifts, moisture gets under the skin.
- Cabinets pulling away from the wall. Failed cabinet screws or missing stud engagement show up as a gap at the top rail. This is a structural issue, not cosmetic, and it needs a look before you load the shelves again.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s how the numbers land in Denton, parts and labor together, with a written price before we touch anything:
| Scope | Installed Range |
|---|---|
| Full kitchen remodel (Atlas-compatible components) | $14,000 – $45,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range: door count, whether the boxes are sound enough to re-front or need full replacement, and whether plumbing or electrical has to move. Every job gets the 365-Day Done Right Promise – a written, full-year guarantee on the completed work. If it fails inside that window, we come back and correct it at no charge.
DIY or Call Us?
You can safely check most of this yourself. Open and close every door and drawer, look for stripped hinge screws, run a fingernail along door edges for lifting laminate, and check whether cabinet runs sit tight to the wall. Measure your overlay and hinge bore and write the numbers down.
Where DIY goes wrong is in the swap itself. Replacing a cabinet run means cutting water and power, leveling to the wall, and shimming correctly – a job that goes bad fast when a supply line or a live circuit is in the way. If you smell gas near the range or see scorched wiring in an outlet box, stop and call a licensed pro. Call (844) 651-3175 and we’ll price it in writing.
FAQs

Twenty to thirty years is realistic for solid boxes, but hardware and door skins fail sooner – usually 10 to 15 years for thermofoil in a humid Texas kitchen. Call (844) 651-3175 for an exact quote – estimates are free.
Often yes. Loose hinges can be re-set with longer screws or a hardwood plug, and a single delaminated door can be replaced without touching the rest of the run. Call (844) 651-3175 and we’ll tell you which path the spec supports.
A single door or drawer box is an hour or two; a full cabinet run with countertop is a multi-day job. We put the schedule in writing before work starts. Call (844) 651-3175 to schedule your free estimate.
We match by series and finish code, quote OEM and quality aftermarket equivalents side by side, and confirm the fit before ordering. Call (844) 651-3175 for pricing on your Denton kitchen.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












