







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Bathroom Remodeling: The Denton Owner’s Guide
CWS bathroom remodeling installed by an independent contractor in Denton typically runs $9,000 – $28,000 for a full bath and $5,000 – $12,000 for a small one, with a written price in hand before any demolition starts. We install CWS-compatible bath systems and components, and we are an independent service provider, not affiliated with CWS.

Owners usually find the problem the same way. A ceiling stain appears below the upstairs bath and the paint keeps bubbling back after each touch-up. The shower pan flexes underfoot near the drain, so you start stepping around it. The caulk line at the tub opens again three weeks after you re-caulk it. Grout at the floor-to-wall joint crumbles into the corner. Or the exhaust fan runs but the mirror still fogs for ten minutes after a shower. Each of those is a symptom of something behind the surface, not the surface itself.
Which CWS Models This Applies To

CWS covers more than one line, and the parts don’t swap cleanly between them. Before anyone orders a pan, a valve cartridge, or a trim kit, we identify what’s actually on the wall and in the slab. The data plate is the starting point: look on the inside rim of the shower pan, the underside of the tank lid, or behind the access panel for a model and serial label. Next come measurements. Pan drain centers shift by fractions between series, and a pan set at a slightly different offset means a new rough-in, which changes the whole scope.
CWS also runs different finish and valve families across its bath lines, and a trim kit from one won’t seat on a cartridge from another. That mismatch is the single most common reason a homeowner buys a part that “fits CWS” and finds it doesn’t fit theirs.
Then there’s the OEM-versus-aftermarket call. For trim, escutcheons, seats, and standard cartridges, a quality aftermarket equivalent is often fine and less expensive, provided the spec sheet matches. For pan assemblies and any structural component, we specify OEM or an exact-spec replacement, because the warranty and the dimension tolerance both matter. Our technicians have up to 22 years of experience reading these labels and catching the mismatch before material gets ordered. On the material side, we work from a documented roster that includes KraftMaid, Cambria, and Silestone along with the fixture brands that pair with CWS-compatible systems, so every spec is traceable.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CWS Bathroom Remodeling Is Failing
- Flex or softness in the shower pan. A pan that gives underfoot or feels spongy near the drain usually means the substrate beneath it has taken on water. Left alone, that moisture travels into framing and subfloor.
- Caulk that fails again within weeks. Repeated caulk failure points to movement, not bad caulk. Either the surround isn’t anchored properly or water is getting behind it and pushing the joint open.
- Persistent fogging and lingering damp air. An exhaust fan that runs but doesn’t clear the room is typically undersized for the cubic footage or venting into the attic instead of outside, which traps moisture in Denton’s humid spring and summer air.
- Grout cracking along the floor-to-wall joint. Hairline cracks that reappear after each regrout signal movement between the wall and floor, often from a pan or liner that wasn’t set on a stable base.
- Staining or bubbling on the ceiling below. Any stain under a second-floor or adjacent bath is an active leak until proven otherwise. This one moves fastest and does the most damage.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

In Denton, a full bathroom remodel runs $9,000 – $28,000, and a small bathroom remodel runs $5,000 – $12,000. The lead range for this page is the full-bath figure. Narrower scopes price out differently: a walk-in shower installation sits at $4,500 – $12,000, a shower replacement at $3,000 – $8,500, a tub-to-shower conversion at $3,500 – $10,000, and a bathroom vanity installation at $800 – $3,000.
What drives the spread: the condition of what’s underneath, whether the rough-in has to move, pan or liner type, tile versus a solid surround, and fixture tier. Every project gets a written line-item price before work begins, with parts and labor broken out, and no numbers that move at the door. All completed work carries the 365-Day Done Right Promise: written guarantee, full year, and if the work fails inside that window we come back and correct it at no charge.
DIY or Call Us?
Some of this you can check yourself, safely. Look for the model and serial label and write down what it says. Measure the pan and the drain center. Confirm the exhaust fan actually terminates outside the house rather than into the attic. Re-caulk a clean, dry joint once and see whether it holds.
Where DIY goes wrong is below the surface. Replacing a shower pan means removing the surround, cutting out the old pan, and rebuilding the substrate with the right slope so water leaves the drain instead of pooling on it. A pan set on a bad base fails the same way the old one did, and you’ve paid for it twice. Tearing into a valve wall has its own risk: a cartridge that won’t seat or a supply line that doesn’t seal turns a weekend project into a shutoff-and-call. We do this work under a written price and a one-year guarantee, so the repair is squared away when we leave. Call (844) 651-3175 for a free estimate and we’ll identify the part before anyone quotes it.
FAQs

A properly installed pan and surround should hold for 15 to 20 years or more, but in Denton that depends on two things: ventilation and the base under the pan. Baths that clear their moisture daily and sit on a stable, sloped substrate routinely outlast that window. Baths with a fan venting into the attic often fail years early. Call (844) 651-3175 for an exact quote on your bath.
Sometimes, yes. A single failed cartridge, a loose escutcheon, or one bad caulk joint is a repair. A pan that flexes, a leak showing on the ceiling below, or grout that keeps cracking means the assembly has to come out. We tell you which one you’re looking at before quoting, and the estimate is free either way. Call (844) 651-3175.
A trim or cartridge swap is usually a few hours in one visit. A shower replacement runs two to four days; a full bathroom remodel runs one to three weeks depending on tile and whether the rough-in moves. You get the schedule in writing with the price, and we don’t start until you’ve seen both. Call (844) 651-3175 for a free estimate.
We match it to your model and serial, not to the word “CWS” in a listing. That means reading the label, checking the spec sheet against your series, and deciding between OEM and a verified aftermarket equivalent based on which component it is. Trim and standard cartridges are often fine aftermarket; pans and anything structural get the exact spec. Call (844) 651-3175 and we’ll walk through what your unit actually needs.
Denton homeowners who’ve been through no-shows and surprise invoices tend to ask the same question first: what’s this going to cost, in writing, before anyone touches the tile. That’s the ask we answer. Call (844) 651-3175 for a free estimate, get a written line-item price, and know exactly what’s covered by the 365-Day Done Right Promise before work begins. A live person answers that line, day or night.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












