







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Roofing: The Denton Owner’s Guide
Bradford Remodeling Co Denton installs and services CWS-compatible roofing systems throughout Denton, with roof replacement running $8,000 – $20,000 and targeted roof repairs $400 – $1,800 depending on the scope. We’re an independent service provider and are not affiliated with CWS. Most owners discover a failing roof the same way: a brown water stain blooms on a ceiling in the back bedroom, a shingle tab shows up in the yard after a wind event, or granules start collecting in the gutters a little heavier every week. Denton sits in a hail belt and swings between hard summer UV and spring supercells, so roofing gets tested from both directions.

Which CWS Models This Applies To

CWS is a real trade name in roofing materials, and the parts that fail are shingles, underlayment, flashing, and ridge or vent components rather than anything electronic. What matters is matching the profile, exposure, and warranty tier your existing system was built around, not guessing a generic replacement. On architectural shingles, the key specs are the exposure (commonly 5-5/8 inches on many three-tab lines versus roughly 8 inches on some architectural products) and the warranty tier, because a mismatched exposure changes the course count and can leave a visible seam or an under-driven nail line.
Identify the right part by pulling a label from a bundle end, checking the paper felt grade on exposed decking, and measuring three shingle courses to get your average exposure. Owners in Denton can usually find the original material on a builder’s spec sheet or a leftover bundle in the garage. On the OEM-versus-aftermarket question for CWS specifically, we source to the manufacturer’s spec where possible so the warranty stays intact, and use a quality equivalent only when the OEM line is discontinued or the timeline doesn’t allow it. Once you know your profile, we can also discuss how a CWS repair ties into other exterior work, like James Hardie siding upgrades or a GAF-registered shingle replacement.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CWS Roofing Is Failing
- Ceiling stains or attic moisture. Water is tracking past underlayment or a flashing joint, which means a specific leak path exists even if the surface looks fine. Catching it early keeps the repair inside the $400 – $1,800 band.
- Granule loss in gutters. Heavy granule shedding signals an aged shingle nearing the end of its service life, common after a decade of Texas UV cycling. Once granules are gone, the asphalt mat starts to break down.
- Lifted or curled shingle tabs. Wind uplift and thermal cycling curl the tabs, and the seal strips lose their grip. A few tab replacements are cheap; ignored curling opens the door to full replacement.
- Nail pops and humped decking. Fasteners backing out or a soft deck section points to moisture intrusion or an installation issue. A humped area usually means the substrate underneath needs attention, not just new shingles.
- Flashing gaps at chimneys and vents. Sealant dries and cracks, and metal flashing pulls away. This is one of the most common leak sources we see in Denton, and it’s often a repair that runs a few hundred dollars rather than a full re-roof.
Replacement Cost & What’s Included
Here are installed price ranges for Denton, kept consistent across our pages so you can plan against a real number rather than a call-for-quote runaround.
| Scope | Installed Price Range |
|---|---|
| Roof Repair (flashing, tabs, small section) | $400 – $1,800 |
| Tile Roof Repair | $600 – $2,500 |
| Roof Replacement (asphalt) | $8,000 – $20,000 |
| Metal Roof Installation | $15,000 – $40,000 |
What drives the range: roof pitch and height, the number of existing layers to tear off, decking condition (soft spots get replaced, not covered), and whether flashing and vents are replaced or reused. Our part-plus-labor pricing is written out line by line before any work starts, and the finished work carries the 365-Day Done Right Promise – if it fails inside that window, we come back and correct it at no charge. We work with documented name-brand materials like GAF, CertainTeed, and Owens Corning, alongside KraftMaid, Cambria, and Silestone on interior work.

See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Roofing is dangerous to DIY, and we say that plainly rather than as a sales pitch. Roof pitch, ladder work at height, and fall exposure are the real risks, and a mis-set flashing joint can quietly leak for months before a ceiling shows it. What an owner can safely check: attic-side moisture and staining, the gutter granule load, visible shingle tabs and nail pops from the ground with binoculars, and gaps at chimney and vent flashings. Where DIY goes wrong is pulling up shingles blindly, resealing over a tired bundle, or covering a soft deck. Our technicians have up to 22 years of experience and will hand you a written price before work starts – call (844) 651-3175 and we’ll walk through what’s actually failing.
FAQs

Asphalt shingle roofing commonly runs 15 – 25 years here, shorter under sustained UV and hail exposure, longer with proper underlayment and ventilation. The deck matters as much as the shingles, so a soft or unventilated roof shortens life. Call (844) 651-3175 for an inspection and a written estimate.
Often yes, especially when the leak is at a flashing, vent, or small section that can be matched to existing shingles. If the shingles are near the end of their life, a full replacement becomes the smarter path over time. We give you a written price on both and let you decide, no pressure either way.
Most asphalt roof replacements on a typical Denton home run one to three days depending on size, pitch, and deck condition. We pull permits and schedule the work so the site is clean and the scope is documented at close. Call (844) 651-3175 to schedule your free estimate.
We source to the manufacturer’s spec when a matching line is available, pulling from documented suppliers rather than guessing a generic equivalent. When the OEM line is discontinued, we set you up with a quality equivalent and explain exactly what changes. Call (844) 651-3175 and we’ll confirm the match before any order.
Schedule Your Free Estimate
If your CWS roofing is leaking, curling, or past its time, we’ll put a written price in your hands before a single tool comes out and stand behind it with the 365-Day Done Right Promise. Call Bradford Remodeling Co Denton at (844) 651-3175 for a free estimate, and we’ll get the scope and the number squared away.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












