







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Belgard Fence Installation: The Denton Owner’s Guide
A full Belgard fence installation in Denton typically runs $3,500 – $9,000 for a standard residential run, depending on linear footage, height, and whether we’re setting new footings or tying into an existing line. That’s the installed number, materials and labor included, given to you in writing before any work starts. We’re an independent contractor and not affiliated with Belgard, but we install their hardscape and fence systems to manufacturer spec.

Owners usually find the problem one of two ways. Either a post has started to lean after a wet spring, or a section of wall or fence has settled and the capstones no longer sit flush. Denton’s shrink-swell clay soil is the usual culprit. It holds water, swells, then dries and pulls away from the footing, and a fence line that looked plumb at install can shift an inch or two within a couple of seasons.
Key Takeaways
- Installed Belgard fence work in Denton: $3,500 – $9,000, quoted in writing first.
- Most failures trace back to footing depth and soil movement, not the block itself.
- We don’t stock or carry parts on a truck; we source to your model and spec.
- Every installation is covered by the 365-Day Done Right Promise.
Which Belgard Models This Applies To

Belgard’s fence and wall systems use interlocking segmental block, and the specific profile matters. Their retaining and freestanding wall lines (the Diamond Pro and Celtik families are the most common on residential fences locally) each have their own block dimensions, and the cap and corner pieces are not interchangeable between them. If you’re matching into an existing run, the block face dimensions and the height profile have to line up or the course won’t sit true.
Identify your system before ordering anything. Look on the back of a loose cap or the underside of a block for an embossed mold mark. Failing that, measure the face width and height of a single block to the nearest eighth of an inch and compare against the spec sheet. The compatibility gotcha most homeowners hit: two Belgard profiles can look identical from the street but differ by a quarter inch in face height, and mixing them leaves a visible step in every course.
On OEM versus aftermarket: for structural block and cap, stay with the manufacturer’s own product so the profile and the warranty stay intact. For the hidden components, like the polymeric joint sand, the geogrid reinforcement, and the footing mix, a quality equivalent is fine and often the smarter buy. You’ll never see those parts again once the job is squared away.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Belgard Fence Installation Is Failing
Walk the line with a level and a close eye. These are the symptoms that matter:
- Posts leaning out of plumb. The footing has lost its grip, usually because soil shrank away from the concrete after a dry Denton summer. A post that moved more than half an inch is telling you the base failed, not the block.
- Stepped or uneven capstones. The runs are settling at different rates, which means the footing depth is inconsistent along the line. Capstones should sit flat and flush; any step means the course below has shifted.
- Joint sand washing out. Polymeric sand breaking down and running out at the joints lets water straight into the wall. Once water gets behind the block, the whole section is a season away from moving.
- Horizontal cracks at the base course. A crack that follows the bottom course is a footing problem, not a surface one. It’s the clearest sign the base wasn’t dug below the local frost-and-expansion line.
- Efflorescence and white staining. That chalky bloom can be normal early on, but if it keeps returning it means moisture is migrating through the block continuously, and the drainage behind the wall needs a look.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For Denton, budget $3,500 – $9,000 installed. Here’s what moves the number:
| Factor | Effect on price |
|---|---|
| Linear footage and wall height | Primary driver; longer, taller runs need more block and deeper footings |
| Footing replacement vs. tie-in | New footings add labor and concrete; tying into sound existing work saves money |
| Site access and demo | Tight side yards and hauling off old block add cost |
| Drainage correction | Fixing what caused the failure is part of doing it right |
Your quote is line-item: block and cap, joint sand, geogrid, footing, demo, and labor, each with a price. The range reflects the whole job, so there are no surprise numbers at the door. Every installation carries the 365-Day Done Right Promise: if the work fails inside a full year, we come back and correct it at no charge.
DIY or Call Us?
There’s a safe middle here. You can absolutely check your own fence: run a level against the posts, probe the joint sand with a screwdriver, look for cracks along the base course, and photograph anything that’s moved. That information helps us quote accurately.
What we’d steer you away from is resetting a footing or rebuilding a leaning section yourself. A Belgard wall carries real weight, and getting a post or base course out safely, setting it below the expansion line, and re-packing it to stay plumb takes equipment and know-how. Get it wrong and you’re back to a lean in one wet season, with the block already paid for. This is where a trained crew earns its keep. Call (844) 651-3175 and we’ll give you a straight written price before any work starts.
FAQs

A properly installed Belgard system should hold for decades, but the realistic weak point in North Texas is the footing, not the block. If the base is dug below the soil’s expansion line and drainage is handled, expect the wall to stay plumb; if the footing is shallow, you’ll see movement within two or three seasons. Call (844) 651-3175 for a free assessment.
Often yes. If only one or two sections have moved and the rest is plumb, resetting the failed footing and re-laying that run is cheaper than a full rebuild. A line with several failing sections usually points to a base problem that justifies starting fresh. We’ll tell you which case you’re in, in writing.
A single-section reset is typically a day. A full fence run takes several days depending on footage, demo, and footing work. We schedule the work and give you the timeline up front, not after we’ve started.
We identify your system from the mold mark or block measurements, then order the matching profile and cap to that spec. We don’t stock parts or carry them on a truck; we source to your model so the profile and warranty stay consistent. Call (844) 651-3175 for a precise quote, and estimates are free.
Whether it’s Belgard fence work or a kitchen quoted with KraftMaid, Cambria, or Silestone, Bradford Remodeling Co Denton runs on The Garrison Standard: a written price before work starts, background-checked and uniformed technicians, and the 365-Day Done Right Promise on every completed project. We’re part of the Garrison Partners family, an independently owned and operated business held to the same standard. Call (844) 651-3175 for your free estimate.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












