







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Windows & Doors: The Denton Owner’s Guide
We install and service Unilock-compatible windows and doors for Denton homeowners, and most single-unit replacements land between $4,500 and $15,000 installed depending on unit count, glass package and frame material. Impact-rated units in Denton run $8,000 to $25,000. Installation is scheduled, not same-day, and every job starts with a written price before any tool comes out.

Owners usually find the failure before they see it. A window that won’t latch in August. A door that drags on the threshold after a wet spring. Haze between the panes that wasn’t there last year. Denton sits in a climate that swings from 100-degree summers to hard freezes, and every Unilock unit north of Loop 288 gets worked by that cycle. By the time a homeowner calls us, the symptom is usually a year old and the part has been failing the whole time.
Key Takeaways
- Unilock windows and doors are catalogued by series, not by the label on the glass – the model number is on the frame, not the sash.
- Most failures in Denton trace to seal, hardware or frame movement, not glass breakage.
- Installed single-window replacement: $4,500 to $15,000. Impact-rated: $8,000 to $25,000.
- Sealed-unit replacement can sometimes be done without pulling the whole window – but only if the frame is sound.
- Every installation we complete carries the 365-Day Done Right Promise in writing.
Which Unilock Models This Applies To

Unilock builds window and door lines across several series, and the part that fits one series will not fit another. The identifying information is stamped on the frame, usually on the head jamb or the side jamb behind the sash – not on the glass, and not on the manufacturer label on the sill. Open the sash or the door panel and look up and to the side. You’re hunting for a series code and a date-of-manufacture stamp. That pair is what lets us match the right replacement part the first time.
Here’s the compatibility gotcha that costs Denton homeowners the most: Unilock has revised its sash and hardware profile over the years, and a replacement sash ordered against the wrong revision won’t seat in the frame even though it looks identical on the spec sheet. We’ve seen this on doors where the hinge prep spacing changed by an eighth of an inch between revisions – the new panel hangs, but it never closes flush. Measure your existing sash height, width and hinge prep before you order anything. Photograph the stamp. That photograph is worth more than any model number you remember.
The OEM-versus-aftermarket decision for Unilock is straightforward. OEM parts are the surest fit and carry the manufacturer’s own warranty, but lead times run longer and the price reflects it. Quality aftermarket equivalents – the ones from established hardware makers with published specs – are often half the cost and function identically when the series match is correct. Where we won’t compromise is the sealed glass unit. On a Unilock window, the sealed unit is where the energy performance lives, and a bargain unit will fog inside two summers in this climate. We source sealed units from makers with documented specs, and we tell you which one we’re using and why.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Windows & Doors Is Failing
These are the five symptoms we see most in Denton, and what’s actually causing each one.
- Fogging or condensation between the panes. The seal on the sealed glass unit has failed, letting moisture in. This is the most common Unilock window failure we see in Denton, and it’s a glass-unit problem, not a frame problem.
- The window won’t latch, or latches loosely. The lock hardware has worn, or the sash has shifted out of square. On older Unilock units, worn lock cams are the usual culprit; on newer ones, it’s frame movement from settling.
- The door drags on the threshold or sticks at the top corner. Either the hinges have sagged or the frame has moved. In Denton’s clay-heavy soil, frame movement shows up two to three years after a dry summer, not immediately.
- Drafts or visible daylight at the frame. Weatherstripping has compressed and failed. It’s a cheap part, but it’s also the first sign the unit is losing its seal against the rough opening.
- Water staining on the interior sill or wall below the window. This is the one to take seriously. It usually means the exterior seal or flashing has failed, and water is getting behind the frame rather than just past it.
One honest note on the last item: staining on the sill almost always means the problem started outside. We check the flashing and the exterior seal first, because replacing the window won’t stop water that’s coming in around the rough opening.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Our installed prices for Unilock-compatible window and door work in Denton:
| Service | Installed Price Range |
|---|---|
| Single window replacement | $4,500 – $15,000 |
| Impact-rated window installation | $8,000 – $25,000 |
What drives the range: how many units you’re replacing, the glass package (standard versus impact-rated versus low-E), frame material, whether the existing rough opening is sound, and whether we’re doing a full-frame replacement or a pocket replacement that reuses the frame. Pocket replacements cost less but only work when the frame is solid – and on a 15-year-old Unilock unit in Denton, the frame is often the part that’s failing.
Every quote is a written line-item price before any work starts. No number that moves at the door. Parts and labor are separated so you can see what the part costs and what the install costs. Every installation we complete is covered by the 365-Day Done Right Promise – if the work doesn’t hold within a full year, we come back and correct it at no charge. The 365-Day Done Right Promise is a written guarantee, signed and in your hand at close, not a verbal promise.
DIY or Call Us?
Some of this is safe for a homeowner to check. Pop the sash and photograph the frame stamp. Test the lock by closing the window and seeing whether the cam engages fully. Run a hand along the weatherstripping to feel for gaps. Wipe condensation and see whether it returns from inside the glass or just from the room. All of that is safe and it gives us what we need to quote accurately.
What we don’t recommend: pulling a window or door out of the rough opening yourself. A window unit weighs between 40 and 120 pounds depending on size, and a door panel is heavier than it looks. Getting one out of a second-story opening without a second set of hands and the right setting blocks is how people get hurt. Beyond the injury risk, pulling a unit and reinstalling it without proper flashing is the most common cause of the water staining we described above. A window that leaks because it was reinstalled wrong costs more to fix than the original repair would have. If the frame is moving, the flashing is suspect, or the unit is above the first floor, call us. We’ll give you a written price and tell you honestly whether a repair or a full replacement makes more sense for your Denton home.
FAQs

A well-installed Unilock window should last 20 to 25 years on the frame, though the sealed glass unit typically fails first, usually between years 10 and 15 in this climate. Denton’s temperature swings and summer UV load push sealed units harder than in milder markets, so fogging at year 12 is normal, not a defect. Call (844) 651-3175 for a free estimate on replacement – we’ll tell you whether the frame has life left or not.
Often yes. Fogged glass can be fixed by replacing just the sealed unit if the frame is sound, and worn latches or hinges are a hardware swap. But if the frame has moved out of square or the flashing has failed, a repair won’t hold – the underlying problem is the frame, not the part. We’ll inspect and tell you which side of that line you’re on. Call (844) 651-3175 for a free estimate.
A single pocket replacement is typically an afternoon; a full-frame replacement on one unit runs most of a day because the flashing and seal work take longer than the swap itself. Multi-unit jobs are scheduled over consecutive days. We don’t promise same-day service – window and door work is scheduled work, and we’d rather do it right than do it fast. Call (844) 651-3175 to get on the schedule.
We work from the frame stamp and your sash measurements, not from a model number you remember. That combination lets us match the correct series and revision before we order, which is what prevents the wrong-part delivery that eats a week. We source sealed units from makers with documented specs, and we tell you which brand we’re using. Call (844) 651-3175 for a free estimate – we’ll confirm the part match before you commit to anything.
Bradford Remodeling Co Denton is an independent service provider and is not affiliated with Unilock. We also install and service KraftMaid, Cambria, and Silestone products for Denton homeowners.
If you have a failing Unilock window or door and you want a straight answer on repair versus replacement, call Bradford Remodeling Co Denton at (844) 651-3175 for a free estimate. You’ll get a written price before any work starts, background-checked and uniformed technicians on the job, and the 365-Day Done Right Promise covering the work for a full year. A live person answers the phone around the clock – not a voicemail, not a callback queue.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












