







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
American Standard Bathroom Remodeling: The Denton Owner’s Guide
Bradford Remodeling Co Denton installs and remodels bathrooms built around American Standard fixtures, and a full bathroom remodel in Denton typically runs $9,000 – $28,000 when your American Standard tub, toilet, or shower valve stays in the plan. A small bathroom remodel lands between $5,000 and $12,000, and a tub-to-shower conversion on an American Standard tub runs $3,500 – $10,000. We’re an independent contractor, not affiliated with American Standard, and we quote every one of these jobs in writing before work begins.

Denton homeowners usually call us after a slow discovery, not a sudden one. The toilet runs for a few seconds every twenty minutes. The shower valve handle turns but the temperature barely moves. The tub drain won’t hold water anymore. Each of those points to a specific American Standard part that’s reached the end of its life in North Texas water, and the fix depends on which model you own.
Key Takeaways
- A Denton bathroom remodel runs $9,000 – $28,000; a small one runs $5,000 – $12,000; American Standard work stays documented and priced up front.
- The part number on your fixture’s label matters more than the model name on the showroom sticker.
- Denton’s hard water is rough on American Standard valve cartridges and flush valves; those are the first parts to fail.
- Live person answers the phone 24/7 at (844) 651-3175, and the estimate is free.
Which American Standard Models This Applies To

American Standard’s lineup splits into product families, and each family uses a different internal part. The two that show up most in Denton bathrooms are the Champion and Cadet toilet lines and the Colony, Town Square, and Serin faucet and shower trim families. A Cadet flush valve is not a Champion flush valve. A Colony shower cartridge is not a Town Square cartridge. The model name on the lid tells you the family; the sticker under the tank lid or behind the faucet trim tells you the exact part.
Getting the right part starts with an identification step. Pull the tank lid and read the ink stamp on the inside of the tank lid or the side of the tank. On shower and faucet trim, look for the model number etched on the escutcheon plate or stamped inside the handle. If the label is worn off, measure: the valve body diameter, the distance between the rough-in holes, and the spout center-to-center give us enough to match the part.
The OEM-versus-aftermarket call works differently with American Standard than with European brands. American Standard replacement cartridges and flush valves are widely available as genuine OEM parts at plumbing supply houses, so there’s little reason to gamble on a generic equivalent for a valve that lives behind tile. For a toilet fill valve or flapper, a quality aftermarket part like a Fluidmaster is fine and many technicians use them by choice. Our rule at Bradford Remodeling Co Denton is simple: OEM for anything behind a wall, aftermarket only where the part is designed to be swapped in minutes.
What fits which fixture
- Champion toilets: use the Champion-specific flush valve assembly. A generic flapper won’t seat correctly and you’ll get a phantom flush.
- Cadet toilets: the Cadet flush valve and fill valve are standard and easy to match; measure the tank height first.
- Colony and Town Square shower trim: cartridge style differs by trim, so pull the handle cap before ordering.
- American Standard tubs (Princeton, Cambridge, etc.): drain shoe and overflow kits are size-specific; the tub’s slope matters.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your American Standard Bathroom Remodeling Is Failing
Five symptoms we hear most from Denton owners, and what each one actually means.
- The toilet runs in short bursts overnight. A failing flapper or fill valve is leaking water past the seal, and the fill valve kicks on to replace it. In Denton’s hard water, mineral buildup on the flapper seat speeds this up.
- The shower valve handle turns but the temperature barely moves. The cartridge has seized or the pressure-balancing spool inside it has failed. American Standard’s anti-scald cartridges are prone to this after a few years of mineral exposure.
- The tub drain won’t hold water. The overflow gasket has dried out or the drain shoe seal has cracked. Texas heat and long dry stretches between uses accelerate the gasket decay.
- Water pools around the base of the toilet. A wax ring has failed, often after a shift in the floor or a loose closet bolt. Catching this early prevents a rotted subfloor.
- The showerhead drips after shutoff. The cartridge ports are scoring, and the drip is a warning that the cartridge needs replacement before the handle starts leaking behind the trim.
We regularly see the tub-and-toilet combo in older Denton neighborhoods hit several of these at once, because fixtures installed in the same year tend to fail in the same year.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s the honest Denton pricing for American Standard fixture work inside a bathroom remodel:
- Full bathroom remodel: $9,000 – $28,000
- Small bathroom remodel: $5,000 – $12,000
- Tub-to-shower conversion: $3,500 – $10,000
- Shower replacement: $3,000 – $8,500
- Walk-in shower installation: $4,500 – $12,000
- Vanity installation: $800 – $3,000
- Standalone fixture and valve swaps: quoted line by line
What drives you toward the top of a range: substrate repair, moving the rough-in, or adding waterproofing to an older Denton shower. What keeps you at the bottom: reusing the existing rough-in and trim and swapping parts only. Every quote we write breaks out parts and labor separately so you can see what you’re paying for. Every completed job carries the 365-Day Done Right Promise: if our work fails within a year, we come back and make it right at no charge.
DIY or Call Us?
Some American Standard work is safe for owner inspection. Reading the model label, checking the flapper for visible wear, looking for water staining under the tank, checking the cartridge for cracks after shutting off the supply – none of that is dangerous. If you find a swollen flapper or a scored cartridge, you have what you need to order the right part.
Where DIY goes wrong is inside the valve. An American Standard pressure-balancing cartridge holds back the water supply, and if the shutoff is tired or the cartridge is mineral-welded to the bore, an owner ends up with water at the wall and no way to stop it. Shower cartridges and toilet flush valves are not hard, but they punish anyone who rushes the shutoff. If you’re not sure the shutoff will hold, don’t start. Call us and we’ll take a look. We also work with KraftMaid, Cambria, and Silestone when your remodel goes beyond the fixture.
Call (844) 651-3175 for a free estimate. We answer the phone live, 24 hours a day.
FAQs

Expect a shower cartridge to last roughly 5 to 10 years and a toilet fill valve 4 to 8 years in Denton’s water. The mineral load in North Texas water shortens both, especially if the home has no softener, and parts on the edge of that window are the ones we replace most often.
Sometimes yes, and we’ll tell you when. A scored American Standard flapper seat can often be cleaned and reseated, and a lightly scaled cartridge can sometimes be cleaned and lubricated. A cracked cartridge body, a warped flapper, or a failed pressure-balancing spool cannot. We look first, quote honestly second.
A toilet fill valve or flapper swap runs 20 to 40 minutes. A shower cartridge replacement takes 45 to 90 minutes once the supply is verified shut. If the cartridge is seized and needs extraction, it can run longer, and we’ll say so before we start.
We verify against the model and serial sticker, the trim model number, and physical measurements of the valve or flush assembly. Then we confirm the part against American Standard’s part number for your specific model line, not a generic cross-reference. That double-check is why we rarely get a wrong part call-back.
Not without your written approval. Our price is written before any work begins, and change order pricing only appears if we open a wall and find something that wasn’t visible at the estimate. That’s the Garrison Standard: no numbers that move at the door, ever.
Call (844) 651-3175 for a free estimate and a written price before any work starts.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












