







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Fence Installation: The Denton Owner’s Guide
Barrette fence installation in Denton typically runs $3,500 – $9,000 installed, depending on linear footage, series, and how much of the old run has to come out. We install and repair the full Barrette line, and we’ll give you a written price before any work starts. Most Denton owners discover the problem the same way: a post leans after a storm, a gate sags and drags the latch, or a section of panels racks out of plumb and won’t hold a straight line anymore.

Barrette builds strong vinyl systems, but the parts do have a service life. The failure usually starts small and quiet, then shows up all at once when the ground moves or the temperature swings. That’s when the phone call happens.
Which Barrette Models This Applies To

Barrette makes several residential fence systems, and the parts don’t swap across them. The two you’ll see most in Denton yards are the Barrette Select line and the heavier Barrette Sierra privacy systems, with the Barrette Arden and Barrette Harbor styles filling out the residential catalog. Each has its own post size, rail profile, and picket wall thickness, so the right part depends entirely on which system you have.
Here’s how to identify yours before you buy anything. Look for the manufacturer label on the inside face of a panel, usually near the bottom rail; it carries the series name and a part code. If the label is gone, measure the post: a nominal 5-inch post is common on Select, a true 5-inch square on Sierra, and the rail thickness runs roughly 1.5 to 1.75 inches depending on the line. Those measurements matter because a Sierra rail won’t seat in a Select post and vice versa.
On the OEM-versus-aftermarket question, the honest answer is this: for structural parts like posts, rails, and caps, use the Barrette-spec part. The savings from a generic equivalent are small and the fit problems are real, especially on a rail that has to slide through a routed post. For hardware like hinges, latches, and drop rods, a quality aftermarket part is fine as long as it’s rated for the gate weight. We’re an independent service provider and not affiliated with Barrette, but we source to their specs.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Fence Installation Is Failing
Denton sits on clay-heavy soil that swells when it’s wet and shrinks hard in the summer. That movement is behind most of what we see. Here’s what failure looks like, and what’s causing it.
- Posts leaning after heavy rain. The post hole has lost its footing, usually because it wasn’t set deep enough or the concrete collar cracked. Once a post moves, the whole run racks with it.
- Panels sagging or bowing in summer heat. Vinyl expands and contracts with temperature. If the rails were set too tight against the post, they bow instead of floating the way they should.
- Cracked rails at the post joint. Repeated movement at the connection point fatigues the rail. A hairline crack at the post pocket is the first stage.
- A gate that drags or won’t latch. The gate post has shifted, or the hinge hardware has worked loose. Left alone, the gate racks and can bind hard enough to damage the frame.
- Sun-chalked, brittle panels. UV exposure over years dulls the finish and makes the vinyl brittle. North Texas sun is tough on any vinyl, and it shortens the service life compared to cooler climates.
Replacement Cost & What’s Included

For a Denton Barrette fence installation – whether it’s a full new run or a partial replacement after storm or post failure – the installed price lands between $3,500 and $9,000. What drives the range is linear footage, the series you’re installing, gate count, and site conditions like old concrete footings that have to be dug out or a run that follows an irregular property line.
Here’s where the range comes from, line by line:
- Materials (Barrette-spec panels, posts, rails, caps): roughly 40 – 55% of the total
- Labor for demo, digging, and setting posts: the largest variable
- Concrete for post footings: priced by the hole, deeper sets cost more
- Gates and hardware: adds to the total per gate
- Permit, if your Denton run requires one: pulled and inspection passed before we call it done
You get a written, line-item price before any work starts. No numbers that move at the door. Every completed installation is covered by our 365-Day Done Right Promise – for a full year, if the work fails, we come back and correct it at no charge.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some things you can check yourself, and should. Walk the run and look for lean at each post. Measure the gate reveal on both sides; if one side is tighter than the other, the post has moved. Check the label on a panel so you know which Barrette series you’re dealing with. Those are all safe, useful things to do.
Where DIY goes wrong on a fence is in the ground and in the weight. Digging out a failed concrete footing is heavy, physical work, and a poorly set replacement post fails again within a season or two. A gate frame carries real weight, and a racked gate can drop if the hinge hardware isn’t installed to spec. If the failure is post-related or the run has racked, that’s a two-person job with the right tools and the right spec. Call (844) 651-3175 and we’ll take a look. A live person answers, day or night, and the estimate is free.
FAQs

Expect roughly 20 to 25 years for the vinyl itself, though Denton’s sun and clay soil usually mean the posts and connections need attention well before the panels do. The vinyl doesn’t rot, but UV exposure and ground movement are the two things that shorten the real service life. Call (844) 651-3175 for a free inspection and a written assessment.
Often yes. A single cracked rail, a leaning post, or a loose gate hinge can usually be repaired without replacing the whole run, and that’s usually the right call if the panels are still in good shape. If several posts have moved or the panels are chalked and brittle, a full replacement makes more financial sense. We’ll tell you which one you’re looking at, in writing. Call (844) 651-3175 to get a price.
A typical partial replacement or post repair is a one-day job; a full run on an average Denton lot runs two to three days once materials are on site. Weather and ground conditions can add time. You get the timeline in writing before we start. Call (844) 651-3175 to schedule your free estimate.
We match to your series using the panel label or field measurements, then order the Barrette-spec part – post, rail, cap, or hardware – to fit that exact system. We don’t stock parts and we don’t carry them on a truck, so the correct part gets ordered to your job, not improvised. Every install is backed by the 365-Day Done Right Promise. Call (844) 651-3175 and we’ll confirm fit before anything is ordered.
Get a Written Price on Your Denton Fence
Bradford Remodeling Co Denton is part of the Garrison Partners family, independently owned and operated and held to The Garrison Standard: a written price before any work starts, background-checked and uniformed technicians on every job, and a live person on the phone 24/7. Beyond fencing, we work with a documented roster of premium brands – KraftMaid, Cambria, and Silestone among them – so specifications stay traceable. If a Barrette part has failed or your run needs a straight answer on repair versus replace, call (844) 651-3175 for a free estimate. We’ll put the scope, the price, and the 365-Day Done Right Promise in your hand before a single tool comes out.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












