







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Home Additions & ADU: The Denton Owner’s Guide
We install Boral-clad home additions and ADUs across Denton, including accessory structures finished with Boral siding and trim, and the typical installed cost runs $45,000 – $130,000 for an addition and $90,000 – $220,000 for a full ADU, with a written price before we lift a tool. This isn’t a same-day swap: a real addition or ADU is a scheduled build, and we quote it that way.

Denton owners usually discover a Boral failure by touch, not by sight. A walk down the side of the house turns up a trim board that flexes where it should be solid, siding that’s gone chalky and soft under a fingernail, or a section that swelled and popped its fasteners after a summer of heat followed by a spring storm. Boral’s composite and engineered products hold up well in North Texas, but they’re not indestructible, and when a piece fails it usually fails at a joint or a cut edge where water got in.
Which Boral Models This Applies To

Boral makes siding, trim, and shake-style products under several lines, and the piece that fits depends on which one is on your house. Boral’s composite siding line (often sold as Boral TruExterior and similar engineered products) is dimensionally stable and takes paint well, while Boral’s shake and trim profiles come in specific thicknesses and face widths. The compatibility gotcha: a nominal 4/4 trim and a full 1-inch thickness are not the same board, and swapping one for the other throws off the reveal at every joint and seam around windows and doors. On an addition or ADU we match the existing profile thickness, face width, and lap exposure so the new run reads as one continuous wall, not a patch.
Identify your product before ordering. Look for a stamp, label, or printed code on the back of a loose board or inside a scrap piece in the garage; if there’s none, we measure the actual thickness with a caliper and match the profile against known Boral dimensions. On the OEM-versus-aftermarket decision: for a full addition or ADU the material is spec’d and documented from the start, so traceability matters more than saving a few dollars per board. We source Boral-compatible material through documented suppliers with manufacturer specs, and we state plainly what’s OEM and what’s a quality equivalent. Bradford Remodeling Co Denton is an independent service provider and is not affiliated with Boral.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Home Additions & ADU Is Failing
- Soft, chalky siding that pits under a fingernail. UV exposure over many Denton summers breaks down the surface, and once the face goes soft, paint won’t bond and the board keeps degrading.
- Swelling or waviness along a seam. Water has reached the cut edge or a joint that wasn’t sealed right, and the board is absorbing it. This is common on additions where the transition to the original house was never flashed correctly.
- Popped or backing-out fasteners. Boards that move with heat and moisture pull their nails over time, which opens gaps for water and eventually lets the piece loosen.
- Staining, mold, or a musty smell at the wall base. Siding or trim failure lets moisture into the substrate behind it, and the framing or sheathing starts to show it before the exterior does.
- Cracks or a hollow sound when you tap it. Impact damage from hail, or a piece that’s dried out and gone brittle, will crack at the edge or sound dead when tapped.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a Denton addition or ADU, installed pricing runs $45,000 – $130,000 for an addition and $90,000 – $220,000 for a detached or attached ADU, with Boral-compatible siding and trim factored into the scope. What drives the number: the square footage, whether it’s a slab-on-grade or pier-and-beam footprint, how much matching of existing Boral profile and exposure is needed, and whether you’re adding a full bath or kitchenette rough-in. We hand you a written line-item price before any work starts, and that number doesn’t move at the door.
Parts and labor are broken out so you can see what the material costs versus the install. Every finished Boral addition or ADU we complete carries the 365-Day Done Right Promise: if the work fails inside that year, we come back and correct it at no charge.
DIY or Call Us?
You can safely check a few things yourself: tap along the siding and trim for hollow or soft spots, run a hand along the seams to feel for gaps, and look at the ground line for staining or a musty smell. That tells you whether something’s wrong without opening a wall. Where DIY goes wrong is the repair itself. Replacing a Boral board means matching thickness and exposure, re-flashing the joint, and re-sealing the cut edge, and a missed step just moves the water problem inward. On an addition or ADU, the framing, flashing, and substrate work behind the Boral is structural and moisture-critical, and that’s not a weekend job for a homeowner. We’re background-checked and uniformed, and a live person answers the phone around the clock. Call (844) 651-3175 for a free estimate.
FAQs

How long does Boral siding and trim last in Denton? Boral’s engineered composite products typically hold 25 to 30 years or more when installed with proper flashing and a maintained paint finish, though North Texas heat and hail shorten that on a poorly flashed wall. Call (844) 651-3175 for an exact quote on your addition or ADU – estimates are free.
Can a failing Boral section be repaired instead of replaced? Often yes if the damage is isolated to one board and the substrate behind it is dry; if moisture has reached the sheathing, a local repair won’t hold and the run needs to come off. Call us to look at it before you commit to either path.
How long does a Boral addition or ADU take? A straightforward addition runs several weeks to a couple of months depending on size and inspections; a full ADU takes longer. We give you a written schedule with the price, and we don’t reprice mid-build.
How do you source the Boral material? We match your existing profile and thickness through documented suppliers with manufacturer specs, and we tell you in writing what’s OEM and what’s a quality equivalent. We don’t stock parts and we don’t carry material on a truck. Bradford also installs KraftMaid, Cambria, and Silestone, among other documented brands. Call (844) 651-3175 to schedule your free estimate.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












