







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cambridge Pavers Driveway & Pavers: The Denton Owner’s Guide
Installing a Cambridge Pavers driveway system in Denton typically runs $7,000-$18,000 installed, depending on square footage, base prep, and the Cambridge line you choose. If you’re replacing a failed section or a worn-out entry apron, most Denton jobs are a two- to four-day install once materials are on site, and we schedule them on a documented timeline, not a vague “sometime next month.”

Owners usually find out something’s wrong the same way: a rut forms at the garage apron after a summer storm, a paver pops loose near the street, or a whole corner of the drive sinks after the black clay under it swells and shrinks through a wet spring and a dry August. That sinking isn’t the paver’s fault. It’s the base.
Bradford Remodeling is an independent contractor and isn’t affiliated with Cambridge Pavers.
Key Takeaways
- A paver driveway in Denton runs $7,000-$18,000 installed; replacement of an existing drive runs $5,000-$14,000.
- Cambridge pavers are engineered systems. The base, edge restraint, and joint sand have to match the paver, or the drive fails early.
- Denton’s expansive clay soil is the number one cause of paver heave, rutting, and edge failure here, not the pavers themselves.
- Every Bradford install carries a written price before work begins and the 365-Day Done Right Promise.
- Call (844) 651-3175 for a free estimate; estimates don’t cost anything and estimates don’t obligate you.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Which Cambridge Pavers Models This Applies To
Cambridge makes several paver lines used on residential driveways, and each one has its own thickness, face dimensions, and laying pattern. The names you’ll see on a spec sheet or a box end include Ledgestone, MaytRx, Diamond Pro, and Prescott Wall (that last one is a retaining-wall block, so don’t confuse it with a driveway paver). For driveways specifically, look for a paver that’s at least 2 3/8 inches thick. Anything thinner is patio-grade and will shear under a vehicle in a Texas summer.
To identify what’s already installed, measure a single paver face and check the joint width. Cambridge drive pavers typically measure around 3 3/4 by 7 3/4 inches face dimension, though the exact spec depends on the line and the run. If you’re matching an existing drive, take one paver to a supply yard or measure it precisely; color batches also vary between production runs, so a new batch of “the same” color will read slightly different against pavers that have sat in the sun for a few years. That’s normal and not a defect.
The OEM-versus-aftermarket call matters here. Cambridge pavers are modular, so an exact-match replacement is usually available, but a lookalike from a different manufacturer won’t interlock properly with the existing field. Mixing brands in one driveway is where edge failures start.
Signs Your Cambridge Pavers Driveway & Pavers Is Failing
- Rutting at the garage apron. Water sheds off the roof and hits the driveway before it can drain. The base saturates and softens. This is the single most common failure we see on Denton drives.
- Pavers heaving or tenting. The clay underneath swells after rain and pushes pavers up. It happens over a wet spring, then shows up as a ridge you can feel under the tire.
- Loose or migrating edge pavers. The edge restraint has failed or was never set properly, so the field spreads and joints open up. Once joints open, sand washes out and the whole run starts to shift.
- Joint sand washing away. Denton’s heavy spring storms scour out polymeric or regular joint sand. Without joint sand, pavers chatter and chip at the edges.
- Standing water or a soggy patch after rain. The base isn’t graded to drain. Water sits, the base fails, and the paver above it settles.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what a Cambridge Pavers driveway costs in Denton, installed, with the base work and edge restraint included:
| Job | Installed Price Range |
|---|---|
| New paver driveway install | $7,000-$18,000 |
| Full driveway replacement (removing existing) | $5,000-$14,000 |
| Paver patio install (for comparison) | $3,500-$11,000 |
| Driveway sealing (reseal only) | $250-$700 |
What drives the range: square footage, how much base excavation is needed, whether old concrete or pavers have to be hauled off, and the specific Cambridge line. A straight 400-square-foot apron is far cheaper than a 1,200-square-foot curved drive with a retaining edge.
You get a written, line-item price before any work starts. No numbers that move at the door. And every completed install carries the 365-Day Done Right Promise: if the work fails within that window, we come back and correct it at no charge.
DIY or Call Us?

Here’s the honest split. You can safely inspect your own driveway: check for rutting, tap pavers with a mallet to hear hollow spots, and see whether the edge restraint is intact. That tells you whether you have a real problem. What you shouldn’t DIY is the base work, excavation, plate compaction, and edge restraint resetting. Paver driveways fail because of the base, not because of the pavers, and getting the base right requires a plate compactor, the right aggregate, and a proper slope to shed water. That’s where most DIY paver jobs fail within two summers.
If part of your drive has already failed, don’t wait. Water keeps working on the base every storm. Call (844) 651-3175 for a free estimate and we’ll tell you straight whether you need a repair or a replacement.
FAQs
A properly installed Cambridge paver driveway lasts 25 to 30 years, often longer, if the base and edge restraint are done right. In Denton’s clay soil, the base is the variable that matters most, so a good install with correct sub-base prep is what gets you to that lifespan.
Sometimes, yes. A single rut or a few heaving pavers can often be lifted, the base corrected, and the pavers reset. A drive with widespread edge failure or base washout usually needs a full replacement. We’ll tell you which one you have.
A typical Denton paver driveway install takes two to four working days once materials are on site, depending on square footage and how much old surface has to be removed. The base prep and compaction take the longest and are what make the job hold.
We source Cambridge pavers through supply partners that carry the Cambridge line, and we confirm the exact model, thickness, and color on the written spec before any material is ordered. If color-batch variation is a factor for a partial replacement, we lay that out for you in the estimate, not after the fact.
Bradford Remodeling works with a documented roster of name-brand materials beyond Cambridge, including Belgard hardscaping, James Hardie siding, GAF roofing, Therma-Tru doors, and KraftMaid, Cambria, and Silestone surfaces inside the home. Every price goes in writing first, every completed project carries the 365-Day Done Right Promise, our technicians have up to 22 years of experience, and a live person answers our phone 24/7. Call (844) 651-3175 to schedule your free estimate.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












