







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Driveway & Pavers: The Denton Owner’s Guide
We install CGI-compatible driveway and paver systems in Denton at a typical installed cost of $7,000 – $18,000 for a paver driveway, with a written price in your hand before any work starts. Most Denton homeowners find out something has failed the same way: a paver rocks underfoot near the driveway apron, water pools against the garage slab after a hard rain, or a crack line runs from the street toward the porch. In Denton’s clay-heavy soil, that movement is usually the base telling you it has shifted, not the paver itself. The sooner we look, the less of the system you have to replace.

Key Takeaways
- Paver driveway installation in Denton runs $7,000 – $18,000 installed.
- Concrete driveway installation runs $4,500 – $12,000; full driveway replacement runs $5,000 – $14,000.
- Denton’s expansive clay soil is the most common cause of paver movement we find here.
- Every job comes with a written price before work starts and our 365-Day Done Right Promise in writing.
- We’re an independent remodeler, not affiliated with CGI.
Which CGI Models This Applies To

CGI covers a few different lines of driveway and paver products, and the right replacement depends on which series you’re working with. Some CGI lines are interlocking concrete pavers built to a specific nominal thickness (often 60mm for driveways, 80mm for heavier vehicle traffic), and that thickness has to match what’s already bedded so the new unit sits flush with its neighbors. Others are permeable or larger-format systems where the joint spacing and base depth are part of the spec, not an afterthought.
The reliable way to identify what you have is to measure, not guess. Pull one paver that isn’t load-bearing (never pry at a locked-in unit next to the garage) and measure its length, width, thickness, and chamfer. Photograph the underside and any stamp or molded mark. That measurement set tells us the series family and whether a match is available.
On the OEM-versus-aftermarket question for CGI specifically: if the original line is still in production, an OEM match is the cleanest path for color and dimensional consistency. If it isn’t, a quality aftermarket equivalent with the same thickness and near-identical face dimensions will bed correctly – but expect a color shift on the replaced units, because concrete pavers from different production runs never match perfectly. We’re an independent service provider, not affiliated with CGI, so we quote you the match that works, whether that’s OEM or a documented equivalent from our Belgard and Unilock roster.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Driveway & Pavers Is Failing
Here’s what we actually find on Denton driveways, and what’s usually behind it.
- Pavers rocking or “walking” underfoot. The bedding sand has washed out or the base wasn’t compacted to depth. In North Texas clay, base failure is the leading cause.
- Water pooling at the garage apron or driveway edge. The slope has flattened or a paver has dropped. Standing water against the slab is the thing to fix first – it finds its way to the foundation.
- Joint sand washing out after rain. The joint sand has loosened or the polymeric binder has broken down. Left alone, joints fill with soil and weeds, and the pavers start to spread.
- Crack lines and settled sections over the base. Subgrade movement and poor drainage. Cracked pavers themselves are usually a symptom, not the cause.
- Chipped edges along the drive lane. Traffic loading beyond what the paver thickness was specified for, or a hard freeze on a saturated base. We see this most on driveways that carry heavy trucks.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed pricing in Denton breaks down by scope:
| Scope | Installed Range |
|---|---|
| Paver driveway installation | $7,000 – $18,000 |
| Concrete driveway installation | $4,500 – $12,000 |
| Full driveway replacement | $5,000 – $14,000 |
| Asphalt driveway paving | $3,500 – $9,000 |
| Driveway sealing | $250 – $700 |
| Paver patio installation | $3,500 – $11,000 |
What moves the number: driveway square footage, base depth required for Denton’s clay, whether the subgrade needs correction, paver format and color line, and how much existing material has to be removed and hauled. We give you a written line-item price before any work starts, with no numbers that move once we’re on site. Every completed job carries the 365-Day Done Right Promise: if the work fails within that year, we come back and correct it at no charge.
DIY or Call Us?
An owner can safely do a few things. Pull a loose paver and measure it, photograph the joint sand, and note where water pools after a storm. Those notes help us quote the right fix.
Where DIY goes wrong is the base. Re-bedding a paver onto sand without correcting the subgrade under it is a repair that lasts one rainy season in Denton. Lifting a section without a plan for re-compacting the base and re-sanding the joints leaves you with a section that settles again and spreads its neighbors. And if the failure traces back to drainage against the garage slab, that’s groundwork, not a paver swap. This isn’t a dangerous job like springs or gas – it’s a job where the wrong fix costs you twice. Call (844) 651-3175 and we’ll tell you what it actually needs.
FAQs

A properly installed paver driveway in Denton should hold 20 to 30 years, and the pavers themselves often outlast the base. Lifespan here depends less on the paver and more on base compaction and drainage, because the clay soil moves with moisture. Call (844) 651-3175 for an assessment of what you have.
Often yes. If the pavers are intact and only the base or joint sand has failed, we can lift, re-level, re-compact, and re-sand that section for a fraction of a full replacement. Replacement makes sense when the paver stock is damaged or the base needs total correction. We’ll give you the written price for both and let you decide – that’s the Garrison Standard.
A section repair is usually a one- to two-day job; a full paver driveway install typically runs three to five days depending on square footage and how much base correction is needed. We give you the schedule in writing up front, and a live person answers the phone during the job.
We measure the existing unit and match series, thickness, and face dimensions, then source from our documented brand roster – Belgard and Unilock among them – or an OEM match where the original line is still in production. Kansas City budgets this into the written quote before we order anything. Reach us at (844) 651-3175 to get the match checked.
CGI-compatible driveway and paver work in Denton is the kind of job where the base does the work and the pavers just cover it. Bring us the movement, the water, or the washed-out joints and we’ll give you a straight answer and a written number. Our technicians have up to 22 years of experience, and every job is backed by the 365-Day Done Right Promise. Call Bradford Remodeling Co Denton at (844) 651-3175 for a free estimate.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












