







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Fence Installation: The Denton Owner’s Guide
Fence installation for a CGI product in Denton typically runs $3,500 to $9,000 installed, depending on fence type, linear footage, and whether old fencing or posts have to come out first. We work with CGI-compatible fence systems and give you a written, line-item price before any digging starts. Most owners land on this page after a section of fence has started to lean, a gate has stopped latching square, or a post has pulled loose at the ground line following a run of North Texas wind.

Denton sits on that band of black clay that swells when it’s wet and shrinks hard when it’s dry, and fence posts feel every bit of that movement. A post that was dead plumb in March can be off a couple of degrees by August. That soil reality is why so many fence failures around here are foundation problems wearing a fence costume.
Key Takeaways
- Installed fence pricing in Denton for CGI-compatible systems: $3,500 to $9,000.
- Written price before work starts, every time, under The Garrison Standard.
- Every completed install carries the 365-Day Done Right Promise: if the work fails inside a year, we come back and correct it at no charge.
- Fence and gate work is generally safe to inspect yourself. Structural repairs on a leaning post or a failed gate are where DIY costs homeowners more than it saves.
Which CGI Models This Applies To

CGI fence systems cover a broad family of products, and the compatibility question depends on which series you own. Panel-and-post systems, ornamental aluminum lines, and vinyl privacy systems each use different rail spacings, post caps, and bracket hardware, and they don’t swap between series. The first step is finding the manufacturer label. It’s usually on a post cap, the inside face of a rail, or a tag stapled to the back of a panel; on older installs it may be faded to nothing, which is when measurement takes over.
Measure rail thickness, post face dimension, and the on-center distance between posts. Those three numbers tell us which CGI series you’re working with and whether a replacement component will actually fit. If you can’t find the label, a photo of the post-to-rail connection with a tape measure held against it is usually enough for us to identify the line.
On the OEM-versus-aftermarket decision: original CGI components give you an exact match and the manufacturer’s own warranty backing the piece, which matters on a fence you plan to keep. Quality aftermarket equivalents can match the line visually and cost 20 to 30 percent less, but they carry their own warranty terms, not CGI’s. Neither path is wrong. We tell you which is which and let you decide. Bradford Remodeling Co Denton is an independent service provider, not affiliated with CGI.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Fence Installation Is Failing
- Posts leaning out of plumb. In Denton’s clay soil, the cause is usually water working around the post base and softening the surrounding ground, not the post itself. A post that’s pulled a few degrees off vertical will keep going once it starts.
- Rails pulling free of posts or brackets. Fasteners and bracket hardware loosen as the wood or vinyl around them expands and contracts through temperature swings. This one is often a hardware fix, not a panel replacement.
- Gate sagging or dragging. Hinges carry the full weight of a gate, and a gate that won’t latch square is usually telling you the hinge plate or the gate post has shifted. Gate hardware takes more load than any other part of the fence.
- Cracked or split panels, especially near the ground. UV exposure and moisture cycling stress the panel where it meets the rail. Cracks that start small widen fast through a Texas summer.
- Visible rot, soft spots, or termite damage at the post base. Denton’s humidity gives wood-destroying insects a long working season, and a soft post is a structural problem even if the panel above it looks fine.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For Denton, CGI-compatible fence installation typically runs $3,500 to $9,000 installed. The low end fits a modest run replacing existing panels and posts on the same line; the high end covers longer footage, ornamental or premium vinyl systems, gate rebuilds, and old fence removal and haul-away. Post replacement in clay soil runs higher than in sandier ground because setting a post that stays put takes more concrete and more digging.
Every price we give is written and line-itemed before work starts: materials, labor, removal, and disposal each get their own line. No numbers that move at the door. We install with a documented roster of premium brands, and the same discipline carries into our other work with KraftMaid, Cambria, and Silestone.
The completed install is covered by the 365-Day Done Right Promise. If the fence fails within a year of completion for reasons tied to our work, we come back and correct it at no charge. That’s the whole term, in writing, in your hand at job close.
DIY or Call Us?
You can safely check a lot of this yourself. Walk the line looking for leaning posts, push on rail connections by hand (not with a pry bar), and look at the ground around each post for soft soil or standing water. Take photos with a tape measure in frame. Matching a bracket or a panel to your CGI series is also something you can do with the label and a few measurements.
Where DIY goes wrong is at the structural end. Digging out and resetting a post in Denton clay, rebuilding a gate that’s carried load and shifted, and correcting a fence line that’s out of plumb are jobs where a weekend attempt usually ends with a worse lean by fall. Our technicians have up to 22 years of experience, and they’re background-checked and uniformed, so you know who’s on your property before they arrive.
Call (844) 651-3175 and we’ll talk through what’s actually failing before you spend anything.
FAQs

A well-installed CGI fence typically holds 15 to 20 years for vinyl and ornamental aluminum, with wood-post systems running shorter depending on soil drainage and sun exposure. Denton’s clay soil and summer heat push both ends of that range harder than milder climates, so post setting and drainage matter as much as the panel itself. Call (844) 651-3175 for a free estimate on your specific setup.
Often yes. Loose brackets, gate hinges, and single cracked panels are usually repair jobs, and we’ll tell you plainly when repair is the right call. A fence line where multiple posts have shifted is a different story, and we’ll explain why rather than just quoting a full replacement. Call (844) 651-3175 and we’ll walk through it.
Most residential fence replacements in Denton run one to three days on site, depending on linear footage, gate count, and whether old fencing has to come out. Post setting and cure time can stretch a longer run into a second visit. You’ll get the timeline in writing before we start.
We identify your CGI series from the manufacturer label or from measurements you provide, then source the correct component through our documented material roster. We don’t stock parts and we don’t carry them on a truck; every piece is ordered to your fence line. Call (844) 651-3175 for a free written estimate.
When you’re ready, call (844) 651-3175 for a free written estimate on your CGI fence installation in Denton. A live person answers, day or night, and you’ll have a real number in hand before anything gets dug.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












