







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Windows & Doors: The Denton Owner’s Guide
We install CGI-compatible windows and doors in Denton, and most full window replacements run $4,500 to $15,000, while impact-rated units land between $8,000 and $25,000. If your CGI window or door has a failed seal, a fogged pane, a dragging sash, or a door that no longer latches square, call us at (844) 651-3175 for a free estimate. Owners usually notice the problem in stages: a film of condensation between the panes that never clears, then a draft at the sill, then a latch that needs a shoulder to close. A door that won’t sit square in summer often hints at settling or a worn hinge plate – both common in Denton’s clay-heavy soil, which shifts with wet and dry cycles and can throw a frame slightly out of plumb over time. Bradford Remodeling Co Denton is an independent remodeler; we’re not affiliated with CGI.

Which CGI Models This Applies To

CGI’s residential window lines ship in several series, and the part you need depends on which one you have. The surest way to identify yours: look for the manufacturer’s label in the frame’s top or side reveal, photograph it, and match the series and size code against the glass stamp in the corner of each pane. Vinyl single-hung and double-hung units use different balance cartridges than casement operators, and mixing them is the most common ordering mistake we see in Denton.
The OEM-versus-aftermarket decision comes down to fit and warranty. OEM parts for a CGI window are made to that series, so tolerances match and any remaining manufacturer coverage stays intact. Quality aftermarket balances, weatherstrip, and hardware run roughly 20 to 40 percent less and are fine when the part is generic – a standard sweep or a common sash lock. When the part is proprietary – a casement operator arm, a tilt-latch, a specific hinge – go OEM or a like-for-like equivalent matched to the label, because a near-fit part is what forces a second service call. For a full window or door unit, we install premium documented brands including Therma-Tru doors; we also fit KraftMaid, Cambria, and Silestone in related interior work when a remodel pulls a room together.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Windows & Doors Is Failing
Here’s what Denton owners actually report, and what’s going on underneath each one.
- Fog or condensation between the panes. The sealed glass unit has lost its argon fill and desiccant, so moisture creeps in. A fogged pane means the glass unit itself is failing, not the frame – you can replace the insulated glass unit alone if the sash is sound.
- Drafts or a cold spot at the sill. Weatherstrip has flattened or the frame is out of square from settling. If a straightedge shows the gap widens in one corner, the frame moved, not just the seal.
- A sash that drags or won’t stay open. A balance or spiral rod has lost tension. On vinyl single-hungs, a snapped balance is the usual culprit and the sash will feel slack or slam shut.
- A door that sticks, drops, or won’t latch. Worn hinges, a shifted strike plate, or a frame that has moved. Texas heat and humidity swell doors and soften frames, so a door that worked in March often binds by August.
- Visible rot or soft wood at the sill or threshold. Water has been getting behind the seal for a while. Probe the wood with a screwdriver – if it sinks, the substrate is compromised and patching won’t hold.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Denton, window replacement typically runs $4,500 to $15,000 and impact window installation $8,000 to $25,000, depending on unit count, size, and glass package. A single fogged insulated glass unit costs far less than a full window – the range jumps when the frame, sash, or rough opening is involved. Impact glass and low-E coatings add to the top end; standard vinyl replacements sit at the low end.
- Replacing one glass unit (IGU): the low end of the window range, sash reused
- Full window unit, standard vinyl: mid to high window range
- Full window unit, impact-rated: $8,000 to $25,000 for a whole-house package
- Exterior door replacement: priced within the window range depending on door and frame work
Every quote is a written, fixed price before work starts – no numbers that move at the door. Labor, disposal, and finish trim are spelled out line by line. Work is covered by the 365-Day Done Right Promise: if it doesn’t hold within a full year, we come back and correct it at no charge. Call (844) 651-3175 for a free, exact quote.

DIY or Call Us?
Some checks are safe and save you a service call. You can photograph the label, measure the rough opening and the visible glass, replace a sash lock or sweep, and clean and lubricate a hinge or track. Those are homeowner tasks.
Full unit replacement is where DIY goes wrong. Windows and doors are heavy, they ride in a rough opening that must be flashed and shimmed square, and a poorly set unit leaks and voids the glass warranty. Removing and reseating an exterior door risks a finger or a back, and getting the flashing wrong invites water damage you won’t see for a season. If the frame is out of square, the glass is fogged, or the door has dropped, that’s a job for a trained crew. Our technicians have up to 22 years of experience, and a live person answers the phone 24/7 – call (844) 651-3175 and we’ll give you a straight number.
FAQs

How long do CGI windows and doors last in Denton? A well-installed vinyl window typically lasts 20 to 25 years, and a sealed glass unit often fails sooner, around 10 to 15, because the seal gives before the frame does. Denton’s wide swings between humid summers and dry winters stress seals and push frames, so expect the glass unit to be the first thing to go.
Can a failing CGI window be repaired instead of replaced? Yes – fogged glass, worn weatherstrip, and a slack balance can often be fixed without a new window, which costs far less than full replacement. A rotted sill or a frame that’s out of square usually means replacement. Call (844) 651-3175 for a free assessment and a written price either way.
How long does a window or door swap take? Replacing a single glass unit is usually a short visit, while a full window or door unit typically takes a few hours to most of a day per opening depending on trim and flashing. We give you the schedule in writing before work begins so you know what to expect.
How do you source the right CGI part? We match against the manufacturer label and the glass stamp to confirm the series and size, then order OEM or a like-for-like equivalent. We don’t stock parts or carry them on a truck – the correct part is ordered to your unit, so nothing gets forced to fit.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.
Ready to get your CGI windows and doors squared away? Bradford Remodeling Co Denton puts every price and every guarantee in writing before work starts, backed by our 365-Day Done Right Promise, background-checked technicians, and a live person on the phone around the clock. Call (844) 651-3175 for a free estimate on your Denton project.












