







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Fence Installation: The Denton Owner’s Guide
Fence installation built to KraftMaid specifications in Denton typically runs $3,500 – $9,000 installed, and most projects schedule within a week or two of an approved written quote. If you have a KraftMaid fence component that has failed, you already know the symptoms: a leaning post line, a gate that drags on the slab, cracked pickets after a windy spring, or a section that sags every time the Blackland clay under it gets wet and then bakes. You want the right part matched to your system, a straight number, and a crew that shows up when it says it will. That’s the page you’re on.

One thing to say plainly up front: Bradford Remodeling Co Denton is an independent service provider, not affiliated with KraftMaid. We install and repair to KraftMaid specifications using documented brand materials, and we’ll tell you exactly what’s compatible and what isn’t.
Key Takeaways
- Installed KraftMaid-spec fence work in Denton: $3,500 – $9,000.
- Denton’s expansive clay soil is the leading cause of fence failure here, not the fence panels themselves.
- You get a written price before any work starts, and a 365-Day Done Right Promise on the finished job.
- Our technicians have up to 22 years of experience.
Which KraftMaid Models This Applies To

KraftMaid builds fence systems around a few core series, and the part you need depends on which one you own. The most common residential lines in Denton are the panel-based privacy systems and the modular picket kits. Before you order anything, find the label. It’s usually on the inside face of a post cap, on a rail end, or stamped into the top of a gate stile. The label gives you a series code and a nominal panel width. Measure it yourself anyway: a “6-foot” panel often measures 70 to 71 ½ inches once assembled, and ordering to the nominal number instead of the actual is the mistake we correct most often.
Then comes the OEM-versus-aftermarket decision. KraftMaid OEM parts are the exact match for finish, dimension, and system compatibility. Quality aftermarket equivalents exist for posts, rails, and pickets, and they can save real money, but the fit has to be checked against your series code. We don’t stock parts and we don’t carry them on a truck. We source the correct part for your model, document the manufacturer spec, and install it. KraftMaid is part of a documented brand roster that also includes Cambria, Silestone, and Kohler, so specifications stay traceable from the paperwork to the finished job.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your KraftMaid Fence Installation Is Failing
Fence failure in Denton almost never starts with the panel. It starts underground. Here are the symptoms that tell you what’s actually happening.
- Posts leaning after a rain. Denton’s Blackland clay swells when wet and shrinks when it dries, and that movement pushes posts out of plumb. One or two leaning posts usually means the footings are shallow or weren’t set to depth for this soil.
- Gate dragging or catching. A gate that scrapes the driveway is a hinge or post-settlement problem, not a gate problem. Left alone, the drag puts torsion on the hinge rail and cracks it.
- Cracked or split pickets. Cedar and composite both take a beating in North Texas heat and wind. Hairline cracks along the grain mean the picket has dried past its limit or was installed too tight against the rail.
- Loose or popping rail fasteners. Fasteners that back out after a season point to either the wrong fastener for the material or movement in the post the rail is anchored to.
- Sagging panel tops between posts. A visible dip across a bay almost always means the top rail has lost its bearing or the post spacing exceeds the rated span for your series.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed KraftMaid-spec fence work in Denton runs $3,500 – $9,000 for a typical residential project. A partial replacement of a section, a gate rebuild, or a post reset sits at the low end; a full run with proper footings, hardware, and finish lands toward the top.
What drives the range: linear feet, the series and material, how many posts need footing work, gate count, and whether we’re removing an existing fence. Your written price breaks it into parts and labor line by line, and it doesn’t move at the door. That’s The Garrison Standard in practice, and it’s non-negotiable on every job.

The work is covered by the 365-Day Done Right Promise: if the installation fails within a full year of completion, we come back and correct it at no charge. Specifications use documented brand materials with manufacturer warranties behind them, so quality isn’t left to guesswork.
DIY or Call Us?
Some checks are safe and worth doing yourself. Walk the line and note which posts are out of plumb. Photograph the label and measure the actual panel width. Check whether the gate hinges are tight and whether any fasteners have backed out. That information helps us quote accurately.
Where DIY goes wrong is underground and overhead. Setting a post footing to the right depth and bearing in Denton clay isn’t a weekend job with a hand auger, and a poorly set post means the whole run moves within a season. Fence work doesn’t carry the high-tension or electrical risk of, say, garage springs or panel wiring, but a fence that lets go in a North Texas windstorm is a real property risk, and a bad footing is money spent twice. If your posts are already leaning, the fix is below grade.
Call (844) 651-3175 when you’re ready for a written price. We answer with a live person, 24/7.
FAQs

A properly installed KraftMaid fence should hold 15 to 20 years in Denton, but the panels aren’t the limiting factor. Footings set to depth in Blackland clay decide the lifespan, and posts that weren’t set right fail in 5 to 8 years regardless of panel quality. Call (844) 651-3175 for an assessment and a written estimate.
Often, yes. A single leaning post, a failed gate, or one damaged bay can usually be repaired rather than replaced, and that keeps your cost near the low end of the $3,500 – $9,000 range. The question is whether the footing behind it is sound. We check that first and tell you honestly which way makes sense. Call (844) 651-3175 for a free estimate.
A section repair or gate rebuild usually finishes in a day, while a full fence run with new footings typically takes two to four days depending on linear feet and weather. We give you the schedule in writing before we start. Call (844) 651-3175 to get your project on the calendar.
We identify your series from the label and confirm the actual measurements, then source the correct OEM or quality aftermarket part and document the manufacturer spec. We don’t stock parts and don’t carry them on a truck. Every part is matched to your specific model. Call (844) 651-3175 and we’ll walk you through what your model needs.
When you’re ready for a straight number, call Bradford Remodeling Co Denton at (844) 651-3175. You’ll get a written price before any work starts, background-checked uniformed technicians on the job, and a signed 365-Day Done Right Promise in your hand when we close out. Estimates are free, and a live person picks up the phone.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












