







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Oldcastle Fence Installation: The Denton Owner’s Guide
Oldcastle fence installation in Denton typically runs $3500 – $9000 for a residential yard, with most of that spread coming down to linear footage, material line, and how much old fence and footing work has to come out first. If you’re pricing a repair rather than a full run, we quote that separately, and every number is a written price before any work starts.

Owners usually find us after a wind event, not before. In Denton, a spring squall line rolls through and one section of the old fence is leaning into the neighbor’s yard, or the gate drags and won’t latch, or a post has pulled loose from the concrete at the ground line. By the time you’re standing in the alley looking at it, the question isn’t whether it failed; it’s which part failed and whether it’s worth saving.
One thing to state plainly up front: Bradford Remodeling Co Denton is an independent contractor. We’re not Oldcastle, and we’re not affiliated with Oldcastle. We install Oldcastle fence systems and compatible components because they’re a documented, spec-traceable material line.
Key Takeaways
- Installed Oldcastle fence runs $3500 – $9000 in Denton for most residential lots.
- Vinyl fence falls in that same band at $3500 – $9000; aluminum runs $4000 – $10000.
- Your written price is fixed before any work starts. The number doesn’t move at the door.
- The 365-Day Done Right Promise covers the completed install for a full year. If the work fails in that window, we come back and correct it at no charge.
Which Oldcastle Models This Applies To

Oldcastle’s fence line covers vinyl privacy, semi-privacy, aluminum ornamental, and composite profiles, sold through building supply channels rather than a single model number stamped on a post. That’s the first compatibility gotcha: you won’t find one clean “model” label the way you would on a garage door opener. What you’ll find is a profile name on the packaging or the supplier’s spec sheet, and the actual spec is the fence height, the rail spacing, the picket width, and the post size.
So the identification method we use is measurement, not model-chasing. Pull four numbers: overall fence height in inches, rail spacing from center to center, picket or panel width, and post dimension. For most residential vinyl privacy lines those are 48″, 60″, or 72″ high with 2″ x 3.5″ or 5″ x 5″ posts. Bring those numbers in and matching the correct panel, post cap, or rail end is a clean job. Guess at it and you’ll drive to three suppliers in Denton before you find the right picket cap.
On the OEM-vs-aftermarket call: for structural pieces (rails, pickets, posts, gate hardware) stay with the manufacturer’s matching line, because mixing a 2″ x 3.5″ rail from one profile into a 5″ post system changes the load path and voids the material warranty. For cosmetic bits (caps, brackets, trim) a quality aftermarket equivalent is fine and often cheaper. We carry no parts on our trucks and we don’t stock inventory. What we do is source from a documented supplier roster, order against your measured spec, and put the material make and spec on your written quote so it’s traceable.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Oldcastle Fence Installation Is Failing
Denton weather does specific damage to a fence, and the symptom usually points at the cause. Here’s what to look for:
- The gate drags or won’t latch. A gate that’s been fine for years suddenly scraping means a hinge post has lost its footing, either from soil movement after heavy clay-soil saturation or from a post that was set too shallow in the first place.
- One section is leaning, the rest is straight. That’s almost always a single post, not a fence failure. Getting a diagonal brace on it quickly keeps the rail joinery from pulling apart and turning a post repair into a full panel replacement.
- Pickets cracking or becoming brittle along the bottom. UV exposure in Texas summer sun breaks down vinyl over time. A south or west-facing run will always go first on a Denton yard.
- Posts wobbling in the concrete collar. If the concrete is cracked or the post is loose in the collar, the footing has shifted. A wobbly post under a loaded gate will fail completely and drop the gate, which is the point where safety matters, not just looks.
- Rails pulling out of a post or pickets sliding. That’s usually a mixing problem: the wrong rail profile fitted into a different post pocket, or fastening that was never rated for the load. It looks like a small fix until one wind gust takes the whole panel.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed Oldcastle fence in Denton lands at $3500 – $9000 for a typical residential run. Vinyl fence installs at $3500 – $9000. If you’re going aluminum ornamental, the band is $4000 – $10000. A part-only repair (a hinge post, a section of rail, a gate rehang) sits well below those bands and is quoted as its own line item.
What drives the range: linear footage, fence height, post density, old material removal and disposal, and whether post holes hit the hard Edwards limestone seams that run through parts of Denton. Footer depth matters, and we spec it on paper before we dig, not on the fly. Every quote is line-itemed: material, labor, removal, and disposal, each with its own number. Our technicians have up to 22 years of experience, and every completed install carries the 365-Day Done Right Promise. If the work fails within a year, we return and correct it at no charge.
DIY or Call Us?
What you can safely do yourself: measure your fence height, rail spacing, picket width, and post size to establish the right replacement spec. Check gate hardware for loose screws. Look at whether the concrete at each post is cracked or the post moves in the collar. That’s all useful information, and it makes any quote you get more accurate.
Where DIY goes wrong on a fence is the post footing. The most common failure we see isn’t the panel; it’s a shallow post that seemed solid on a dry day and then moves after a wet week. A loaded gate on a moving post can fall on a person or a pet. That post needs to be dug, set, and cured correctly the first time.
Call Bradford at (844) 651-3175 for a free estimate on your Oldcastle fence project.
FAQs

Expect 15 to 20 years from a properly installed vinyl fence in North Texas, with the last few years of that showing UV fading and picket brittleness before structural failure. Aluminum ornamental often goes longer. How much of that life you actually get comes down to the post footings and the finish quality, not the panel itself.
Yes, and most failing fences can be saved section by section. A leaning panel over one bad post is a repair, not a rebuild. A fence losing posts at multiple locations is usually a footing problem and gets evaluated as a whole. Call (844) 651-3175 for a free estimate, and we’ll tell you honestly which job you’re facing.
A single-section repair is usually a day. A full residential run in Denton runs several days depending on linear footage and site access. The timeline gets written into your scope before work starts, so there’s a documented schedule, not an estimate talked through at the door.
We order against your measured spec from a documented supplier roster and put the material make and profile on your written quote. We carry no parts on trucks and don’t stock inventory, so nothing is substituted at the last minute. Every spec is traceable before the material arrives. Call (844) 651-3175 for a free estimate; we also work with KraftMaid, Cambria, and Silestone on interior projects.
When the job ends, what you should be holding is a clean site, a documented scope, and a signed written guarantee for the year ahead. That’s the job squared away, and that’s what we put our name to. Call (844) 651-3175 to set up your free estimate.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












