







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Denton Owner’s Guide
Schluter bathroom remodeling in Denton runs $9,000 to $28,000 installed, depending on how much of the wet area is being rebuilt and which Schluter system is specified. We install bonded waterproofing assemblies – Kerdi-Board, Kerdi membrane, Ditra-Heat, Kerdi-Line drains and the Kerdi-Fix sealant that ties them together – as part of a full bathroom scope, not as a loose parts swap. If your shower is leaking at a curb, your grout is cracking along a floor seam, or a tile has gone hollow and moving underfoot, the waterproofing layer below it has usually already failed.

Most Denton owners discover this the slow way. A ceiling stain appears in the room below. A musty smell shows up behind a closet wall. A tile “pops” when stepped on near the drain. By the time any of that is visible, water has been sitting in the substrate for weeks or months, and the fix is a rebuild of the shower pan and walls, not a tube of caulk.
Which Schluter Systems This Applies To

Schluter isn’t a bathroom brand with model numbers the way a faucet is. It’s a system of bonded waterproofing components, and the “part” that failed is almost always one of five things. Identifying which one you’re dealing with is the first step, and it’s the step most Denton homeowners skip.
Kerdi-Board is the foam tile backer panel, sold in 1/2-inch, 5/8-inch, and 2-inch thicknesses with a 3/8-inch and 2-inch Kerdi-Band sold separately for seams. Kerdi membrane is the thin sheet rolled over cement board or drywall. Ditra and Ditra-Heat are the uncoupling mats for the floor, and they are not interchangeable with one another – the heated version takes the cable in specific mat sizes. Kerdi-Line and Kerdi-Drain are the linear and point drains, and the drain body, bonding flange, and grate are three separate SKUs that must match. Kerdi-Fix is the sealant, and it has a shelf life that matters.
How to tell what you have: look at the inside face of any cut edge at a shower niche or valve opening. Kerdi-Board reads as a dense orange foam with a fleece face. Kerdi membrane is a thin orange sheet with visible fleece texture on both sides and no foam core. If you find a trowel-notched thinset ridge with no membrane over it, somebody skipped the waterproofing entirely.
On the OEM-versus-aftermarket question: for Schluter specifically, we install genuine Schluter components. The bonding flange tolerances and the fleece face are engineered to work with Kerdi-Fix and unmodified thinset as a matched set; mixing brands at those joints is where leaks start. Bradford Remodeling Co Denton is an independent service provider and is not affiliated with Schluter. We source the correct part, verify the SKU against your existing assembly, and install it. We don’t stock parts and we don’t carry inventory on a truck – the right component gets ordered to your address for the job.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
Most failures we open up in Denton trace back to one of these five symptoms. Each points to a specific cause, and each tells you how far the repair has to go.
- Grout cracking in a straight line along the floor-to-wall seam. That line is a movement joint, and if it was grouted solid instead of sealed with Kerdi-Fix or an approved sealant, the tile and the waterproofing are flexing against each other. Water gets behind the grout on the back side of the first crack.
- A hollow or “bouncy” tile near the drain. The thinset didn’t bond to the fleece face, usually because the membrane was dusty when tile went down. Water finds the void and the tile eventually lifts.
- Mildew that returns within weeks of cleaning. Surface mold on grout is normal in a Texas bathroom. Mildew that comes back in the same spot after a full scrub means moisture is feeding it from behind the tile, and no cleaner fixes that.
- A ceiling stain or soft drywall directly below the shower. The pan has failed – either a puncture in the membrane, an unsealed drain flange, or a curb built without a proper Schluter curb cover. This one moves fast in Denton’s climate.
- Loose or shifting floor tile in the bathroom. Usually a Ditra install where the mat was laid over a wood subfloor with too much deflection or the wrong thinset. Ditra uncouples movement; it doesn’t eliminate a floor that isn’t stiff enough.
One reality specific to North Texas: our soil moves, and it moves more in a dry summer and a wet spring than it did a generation ago. Denton slabs and pier-and-beam floors flex with that cycle. A shower that was watertight at final inspection can open a hairline at a curb seam three or four years later. That doesn’t mean the original install was wrong. It means the assembly needs to be built to tolerate movement, and sloppy ones don’t.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Rebuilding a failed Schluter shower assembly in Denton typically lands in the $9,000 to $28,000 bathroom remodel range, and a smaller repair-limited scope can come in at the smaller end. Here’s what actually drives the number:

| Scope | Installed Range (Denton) |
|---|---|
| Full bathroom remodel with Schluter shower system | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation (Kerdi system) | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement only | $3,000 – $8,500 |
What moves you up or down inside that range: how much tile has to come out to reach the failed layer, whether the drain has to be relocated, whether a Kerdi-Line linear drain is replacing a point drain, and whether heated floor mat is going in. Old tile removal and haul-off is included in every written price. So is a line-item quote showing the Schluter components, the tile, the fixtures, and the labor as separate lines – you’ll see what the part costs and what the install costs, never a lump figure that hides one inside the other. We install Kohler and Moen fixtures in these builds; KraftMaid, Cambria, and Silestone come up when the vanity and countertop are part of the scope.
Every completed remodel carries the 365-Day Done Right Promise: a full year of written coverage, and if the work fails inside that window we come back and correct it at no charge. That’s on top of the manufacturer warranty on the Schluter components themselves. Price is written before any work starts and it does not move at the door.
DIY or Call Us?
There’s a short list of things a homeowner can safely check, and a longer one where DIY goes wrong. Safe to do yourself: look for the orange fleece at a cut edge to confirm what system you have, take photos of the drain grill and any labels, note whether the crack line is grout or caulk, and check whether the ceiling below has a stain. That information makes the estimate faster.
Where it goes wrong: re-grouting a cracked movement joint. Caulking over a wet curb. Setting a tile back over a hollow spot without knowing why it went hollow. Each of those traps moisture against the substrate and hides the real failure until it’s bigger. And the genuinely dangerous part is the demolition itself – you’re prying tile off a substrate with water behind it, near a live electrical circuit if there’s a light or fan in the shower wall. We don’t recommend opening a wet wall yourself. A failed waterproofing layer is not a cosmetic problem, and it doesn’t heal.
If you’re unsure what you’re looking at, call us at (844) 651-3175. A live person answers, day or night, and we’ll tell you straight whether you’re looking at a five-hundred-dollar fix or a full rebuild. Estimates are free and written.
FAQs

A properly installed Kerdi shower assembly should hold 20 to 30 years in a North Texas home. The variable is the substrate and the movement underneath it – not the Schluter product itself, which is why we check floor deflection and substrate condition before we quote. Most premature failures we open in Denton trace to an install shortcut, not a defect in the membrane. Call (844) 651-3175 for an exact quote on your situation – estimates are free.
Sometimes. If the failure is confined to one seam, one drain flange, or a single Kerdi-Band joint that can be exposed without disturbing the tile field, we can cut back to sound membrane and rebuild that section. If water has reached the substrate or the pan, the honest answer is a rebuild – patching over a wet layer just buys you a year. We’ll tell you which one you’re looking at after we open it up.
A shower-only rebuild runs about one to two weeks on site once materials are in hand, with the waterproofing layer needing a full cure before tile goes over it – that cure time is not negotiable and rushing it is how failures happen. A full bathroom remodel runs longer, typically three to five weeks. The written quote includes the schedule, so you know what to expect before the first day.
We order genuine Schluter components to your address for the specific job, sized to your existing assembly, so the drain body, flange, and grate all match. We don’t keep parts in stock and we don’t carry inventory on a truck – the part is ordered when the scope is confirmed. That’s how we can promise the SKU on your written quote is the SKU that gets installed. Call (844) 651-3175 to schedule your free estimate.
Every Bradford Remodeling Co Denton job closes the same way: clean site, documented scope, and a signed written guarantee in your hand. Our technicians have up to 22 years of experience with bonded waterproofing assemblies, and we run every project under The Garrison Standard so the price and the coverage are on paper before any tool comes out. Call (844) 651-3175 for your free estimate on your Denton bathroom.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












