







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Therma-Tru Fence Installation: The Denton Owner’s Guide
If a component on your Therma-Tru fence system has failed, we replace and reinstall it at a typical installed price of $3,500 to $9,000 in Denton, and most straightforward jobs are completed in a single visit. The price depends on the run length, the gate hardware, and how much of the existing structure can be saved. This page is for owners who already know the brand and need the failing part matched, priced, and set right.

Most Denton owners don’t discover a problem all at once. They notice a gate that drags against the post after a wet spring, a hinge that won’t hold tension, or a post cap that has worked loose above a fence line that’s started leaning. By the time the gate won’t latch without a lift, the part has usually been failing for a season. We’re an independent service provider, not affiliated with Therma-Tru, so we’ll tell you plainly when an OEM part is worth the wait and when a quality equivalent will do the job.
Which Therma-Tru Models This Applies To

Therma-Tru fence systems and their gate hardware share a compatibility logic that trips up a lot of do-it-yourself buyers: the gate hardware kit is matched to the gate leaf size and the post profile, not to the run length. A hinge set made for a 4-foot gate won’t carry a 5-foot leaf without sagging inside a year, even if the screw pattern lines up. Before we quote anything, we measure the gate leaf, the post thickness, and the hinge spacing on your actual fence, because the spec sheet alone won’t tell us what’s installed.
To identify what you have, look for the manufacturer label on the inside face of a gate stile or on the post cap. It typically lists the series and the gate width. If the label is sun-bleached or gone, which happens fast in Texas heat, a tape measure and a close look at the hinge screw pattern will usually narrow it down. We also check whether the existing hardware is OEM or a previous aftermarket replacement, since mixing the two is where most of the fit problems start.
OEM parts from Therma-Tru carry the exact finish match and the manufacturer’s warranty backing. Quality aftermarket equivalents cost less and often ship faster, but the finish can be a slightly different sheen, and that matters if you’re replacing hardware on a run that’s still perfectly good. Our technicians have up to 22 years of experience with this decision, and we’ll tell you which route fits your fence rather than defaulting to the pricier one.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Therma-Tru Fence Installation Is Failing
Not every symptom points to the same part. Here’s what we see most in Denton, and what each one usually means:
- The gate sags and drags on the ground. This is almost always worn hinge bushings or a post that’s shifted in soft soil after heavy rain. The gate isn’t the problem; the pivot is.
- The latch won’t catch without lifting the gate. A sagging leaf is pulling the strike plate out of alignment. Left alone, it wears the latch face and the problem gets more expensive.
- Post caps or finials are loose or missing. Sun and wind work the fasteners loose. Exposed post tops let water into the wood or composite, which is the start of a much bigger repair.
- Hardware is rusting or the finish is flaking. Standard steel hardware doesn’t hold up to Denton summers and spring storms. Corrosion in a hinge pin seizes the gate.
- The run is leaning or the posts are wobbly. This is a footing problem, not a hardware problem, and it needs attention before the fence fails completely.
Each of these has a clear cause, and none of them get better with time. If you’re seeing two or more at once, the fence likely needs more than a single part swap.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a Therma-Tru fence installation or a hardware replacement with reinstall in Denton, most jobs land between $3,500 and $9,000 installed. Here’s how the range breaks down:

| Scope | Typical installed price |
|---|---|
| Gate hardware replacement and realignment | $3,500 – $4,800 |
| Partial run reinstall with new hardware | $4,500 – $6,500 |
| Full run reinstall, posts and all | $6,500 – $9,000 |
The price moves on run length, gate leaf count, whether footings need resetting, and whether we’re sourcing OEM or an equivalent part. We give you a written price before any work starts, itemized so you can see the parts and the labor separately, and it doesn’t move at the door. If it’s not done right, our 365-Day Done Right Promise means we come back and correct it at no charge for a full year.
DIY or Call Us?
Some things you can check yourself: tightening a loose post cap, confirming the gate swings free without dragging, and reading the manufacturer label so you know what you’re dealing with. That’s diagnostics, not repair. Where DIY goes wrong is the hinge and post work. A sagging gate is carrying real weight, and pulling hinges off a loaded leaf without bracing it first can drop the gate on you or crack the post. Resetting a footing is a different job entirely and needs the post pulled, the hole redone, and the fence leveled.
We’d rather you call and get a straight price than hurt yourself or make the repair bigger. We answer the phone with a live person, day or night, so call (844) 651-3175 and we’ll tell you what we’re looking at and what it costs.
FAQs

Quality hardware on a properly set post typically holds for 10 to 15 years, but Denton’s heat and spring storms shorten that if the finish fails. Checking hinge pins and post tops each spring will extend the life considerably.
Often, yes. A worn hinge bushing or a loose cap can sometimes be repaired rather than swapped. We’ll look at the actual condition and tell you honestly if a repair will hold or just delay the replacement. Call (844) 651-3175 for a free look.
Most single-gate hardware replacements are done in a single visit, a few hours on site. A longer run or footing work runs longer, and we’ll give you the timeframe in writing with your price.
We identify your Therma-Tru model, then source the correct OEM part or a quality equivalent and tell you which one we’re using and why. You’ll see it itemized on your written quote before work starts. We don’t claim to stock parts on a truck: every part is ordered to your fence. Our documented brand roster also includes KraftMaid, Cambria, and Silestone for the rest of the home.
Call (844) 651-3175 to schedule your free estimate. We’ll come out, measure your fence, and hand you a written price before any tool comes out.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












