







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Denton Homeowners Choose Toto Construction
Bradford Remodeling Co Denton provides independent Toto fixture installation and repair across Denton, and the difference is where we put our attention: rough-in dimensions, flange height, supply placement, and OEM valve parts rather than a generic install. We’re an independent remodeler, not a Toto-authorized dealer or service center, so our advice isn’t tied to a manufacturer program. What we offer is straight trade knowledge about what actually fits, seals, and lasts in North Texas bathrooms.

Denton is a specific place to do that work. The historic blocks around the Courthouse-on-the-Square sit on blackland prairie clay that expands and contracts hard through wet springs and dry summers, so pier-and-beam floors shift and a toilet that sat flat in 2019 may rock like a seesaw in 2026. Toto products show up constantly in Denton remodels: Drake and Ultramax toilets, Washlet seats, faucets. If you need someone who knows the difference between a worn flapper and a bad fill valve without guessing, call (844) 651-3175.
Why Trust Bradford Remodeling Co Denton for Your Toto Construction?

Our technicians have up to 22 years of experience, and a good portion of that is spent on the plumbing-side details that decide whether a Toto fixture sits right. We know that a Drake CST743 two-piece and an Ultramax II one-piece fail differently, that the spud washer is usually the culprit when a tank-to-bowl joint weeps, and that a Washlet S550e with a weak spray is almost always a clogged inlet screen or a tired solenoid rather than a dead unit.
Toto makes OEM fill valves, flappers, gaskets, and spud washers for current production lines, and we use them wherever they exist because aftermarket equivalents change flush volume and seating geometry. That matters more than it sounds. A flapper that closes a hair slower than spec turns a clean flush into a phantom refill at 2 a.m.
Warranty-safe practice is part of the job. We don’t drill, cut, or modify a Toto bowl or tank wall to make something fit. If a rough-in has to move, we say so and quote it in writing before anything is touched. Every completed job carries the 365-Day Done Right Promise: if the work fails inside a full year, we come back and correct it at no charge. That’s the Garrison Standard, and it’s written down before a tool comes out.
Homeowners in Denton also get a written price up front, background-checked uniformed technicians, and a live person on the phone at any hour. No voicemail queue.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Toto Construction Problems We Fix in Denton
Here’s what actually fails on Toto fixtures, and why.
- Washlet and Washlet+ seats that stop spraying, spray weakly, or won’t power on. The S550e, C5, and K300 all pull water through a small inlet screen before it reaches the solenoid. Denton’s hard water loads that screen with scale over a season or two, and the solenoid itself wears out from cycling. Most weak-spray complaints trace straight to one of those two parts, not to the seat’s electronics.
- Slow seepage at the base of a Drake or Ultramax toilet. On Drake CST743 and CST454 series toilets, the tank-to-bowl gasket and spud washer compress over time. You’ll see a faint ring at the base, or a toilet that won’t sit flat after a tile floor goes in. A new floor raises the finished height, and the old flange no longer lines up. The fixture rocks, the wax seal gives, and the seep starts.
- Phantom refill cycles and weak flushes. A toilet that runs for a few seconds hours after a flush is usually a worn flapper or fill valve, not a clog. The flapper loses its seal, water trickles from tank to bowl, the fill valve tops the tank back up, and it repeats. Homeowners in Denton often assume a blockage and reach for a plunger. The tank is the actual problem.
- Comfort-height and elongated Toto bowls that don’t fit the existing rough-in. Toto comfort-height bowls sit taller and many are elongated, which changes clearance to the vanity and to the wall. On older Denton homes near the Square, where the flange or supply stub-out may be off by an inch or more, a standard set-down turns into a re-set with the floor open.
- Old flush valves in Toto tanks that no longer match the bowl. When a previous owner swapped in a generic valve to stop a leak, the flush volume drifts off spec. The bowl doesn’t scour clean, and the cycle gets louder. It’s a five-minute diagnosis and a parts-correct fix.
Toto Parts & Our Repair-vs-Replace Approach

We source Toto OEM fill valves, flappers, gaskets, and spud washers for every job where those parts still exist. That’s the default. When a part is discontinued or on a long lead time, a quality aftermarket valve is a reasonable stopgap, and we tell you plainly that it may not match original flush performance. We don’t claim to stock Toto parts locally. Parts get ordered to the job, and you see the line item before we order.
Repair or replace comes down to three things. If the bowl and tank are sound, we repair. If the bowl is cracked, the glaze is gone, or the rough-in itself has to move, replacement is the honest answer. We’ll say which one and why, and give you the written price for both so you’re choosing with real numbers in front of you. Call (844) 651-3175 for an exact quote. Estimates are free.
Our Toto Service Process – Step by Step
- 1
Diagnosis. We pull the tank and check the fill valve, flapper, spud washer, and tank-to-bowl gasket. For a Washlet, we test the inlet screen and solenoid before touching the electronics. We also check the rough-in, flange height, and floor contact, since a Denton pier-and-beam floor may have shifted since the fixture was set.
- 2
Repair or install. OEM parts go in. If it’s a new fixture or a remodel, we set the flange and supply to Toto’s spec, run power for a Washlet+ seat where it’s needed, and confirm clearance to the vanity and wall before setting the bowl.
- 3
Test. Multiple flush cycles, a full tank refill check, a spray test on every Washlet function, and a rock test on the floor. We don’t leave a fixture that needs a shim to sit flat.
- 4
Warranty and close. Clean site, documented scope, and the signed 365-Day Done Right Promise in your hand. If the repair or install fails within that year, we return and correct it at no charge.
See the difference
Before
After
Before
After
Before
AfterToto Products We Service & Install in Denton
We work on the Toto lines that actually turn up in Denton homes. That includes Drake and Drake II two-piece toilets (CST743 and CST454 series), Ultramax II one-piece comfort-height toilets, and Washlet and Washlet+ bidet seats, including the S550e, C5, and K300. On the tank side, we replace EcoPower and standard Toto flush valves and fill valves. We also handle rough-in work for Toto faucets and fixtures in kitchen and bath remodels, and we match Toto finish and trim across a project so the hardware reads as one set rather than a mix of brands.
We Also Service These Brands
Toto is one line in a bigger toolbox. Bradford Remodeling Co Denton also works with KraftMaid cabinetry, Cambria and Silestone surfaces, and Kohler fixtures, along with GAF roofing, James Hardie siding, and Therma-Tru doors. That matters on a full bath or kitchen remodel where the toilet, vanity, counter, and fixtures all need to land in the same room without fighting each other. You get one crew accountable for the whole scope, not three trades blaming each other.
FAQs – Toto Construction Service in Denton

No. We’re an independent remodeler, not a Toto-authorized dealer or service center, and we don’t represent any manufacturer program. What that means for you is straightforward: our recommendations come from what fits and lasts in North Texas bathrooms, not from a dealer agreement. We use genuine Toto parts where they exist and tell you when we can’t.
Yes, wherever Toto still makes the part. Fill valves, flappers, gaskets, spud washers, and tank-to-bowl seals all get OEM parts on current production lines like the Drake CST743 and Ultramax II. When a part is discontinued or on a long lead, we’ll offer a quality aftermarket valve as a stopgap and tell you plainly it may not match original flush performance. You’ll see the part and the price on the written quote before we order.
Most single-fixture repairs finish in one visit. A fill valve, flapper, or spud washer swap runs well under an hour. A Washlet inlet screen and solenoid repair takes a bit longer because we test every function before we call it done. When a rough-in has to move or the floor has to come up, that’s a scheduled job with a written scope and a timeline you see up front.
Drake and Drake II two-piece toilets (CST743 and CST454 series), Ultramax II one-piece comfort-height toilets, Washlet and Washlet+ bidet seats including the S550e, C5, and K300, and EcoPower and standard Toto flush and fill valves. If your model isn’t listed, call (844) 651-3175 and we’ll confirm coverage before scheduling.
Toto’s warranty covers manufacturing defects, and routine service by a qualified independent pro doesn’t void it. What can affect coverage is modifying the fixture itself, like drilling a tank wall or cutting a bowl to force a fit. We don’t do that. If a rough-in is wrong, we move the rough-in and quote it in writing rather than altering the fixture.
Toto work usually runs as part of a bathroom project in Denton, and here are the ranges we quote. A single-fixture repair like a fill valve or Washlet solenoid is the smallest line on the invoice. The bigger numbers below are the remodel scopes that Toto fixtures typically sit inside:
| Service | Price range in Denton |
|---|---|
| Bathroom Remodel | $9,000 – $28,000 |
| Small Bathroom Remodel | $5,000 – $12,000 |
| Walk-In Shower Installation | $4,500 – $12,000 |
| Tub-to-Shower Conversion | $3,500 – $10,000 |
| Bathroom Vanity Installation | $800 – $3,000 |
Every price we give is written before work starts, and it doesn’t move at the door. Call (844) 651-3175 for an exact quote. Estimates are free.
Book Your Toto Service in Denton, TX
If a Drake keeps refilling, a Washlet sprays weak, or a bathroom remodel needs a Toto fixture set right the first time, call Bradford Remodeling Co Denton at (844) 651-3175. You’ll get a written price before anything starts, background-checked technicians, and the 365-Day Done Right Promise on the finished work. Estimates are free.
Written by the team at Bradford Remodeling Co Denton.












