







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Fence Installation: The Denton Owner’s Guide
Unilock fence installation in Denton typically runs $3,500 to $9,000 for a residential run, priced in writing before any work starts. Unilock is a hardscape brand, so what most Denton owners are actually calling about is a segmental retaining or freestanding wall system doing fence duty, or a fence built to match Unilock pavers and caps. We install and correct both, and we match the system to your existing block profile rather than guessing.

Owners usually find the problem the same way: a course of block has shifted after a wet spring, a cap is loose, or the fence line has started to lean toward the neighbor’s yard. That lean is rarely the block. It’s almost always the base, the footing, or the drainage behind it, and it shows up fast in Denton’s expansive clay soils after a heavy rain.
Key takeaways
- Installed range for a Unilock-compatible fence in Denton: $3,500 to $9,000.
- Most failures are base, footing, or drainage problems, not the block itself.
- Written price before work begins, and a 365-Day Done Right Promise on completed work.
- We’re an independent contractor, not affiliated with Unilock.
Which Unilock Models This Applies To

Unilock makes several wall and freestanding systems that get used as fence lines. The common ones in this market are segmental retaining wall blocks and freestanding garden wall units, plus coordinating caps and coping. If your fence uses Unilock block, it’s likely one of these wall systems set on a compacted base. The product name is usually stamped or molded on the bottom or back of a block, so pull one loose cap and check before you order anything. Our technicians have up to 22 years of experience reading these profiles, and we’ll measure the block dimensions and note the profile so the replacement matches.
Here’s the compatibility gotcha: Unilock block profiles change over the years, and an older run may not match a current block name for name. A block that looks identical on the face can differ by a fraction of an inch, which shows up as a wavy course once it’s stacked. We match by measured dimension and profile, not by the name on the pallet.
On OEM versus aftermarket: for a Unilock system, an OEM-matched block keeps the color, texture, and dimension consistent with what’s already there. A quality aftermarket block can work for a small repair, but check the dimensions against your existing course first. We special-order to match, we don’t keep parts on a truck, and we won’t tell you we do.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Fence Installation Is Failing
- A section leaning toward one side. The base wasn’t compacted enough or the footing has moved. In Denton’s clay, water saturating the base is the usual trigger.
- Loose or missing caps and coping. Adhesive or the cap course has failed, and each rain loosens the next one. Once caps let go, water gets into the core of the wall.
- Blocking that’s settled unevenly along the run. Uneven settlement means the base prep was thin in that spot. It won’t fix itself and it gets worse each wet season.
- Drainage pooling at the base. Water collecting behind or at the foot of the fence line is the number one killer of these systems. It softens the base and pushes the wall out.
- Cracks or spalling on block faces. Freeze-thaw in North Texas and long dry spells followed by heavy rain can crack block faces. Cosmetic at first, a structural warning once it runs deep.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed Unilock-compatible fence work in Denton lands in the $3,500 to $9,000 range. Price moves on run length, how many courses, whether the base and footing need rebuilding, and whether the block profile has to be special-ordered to match. A small section repair sits near the bottom of that range; a full re-set with new base and original-profile matching sits near the top.
- Base and footing rebuild: where the failure actually started.
- Block, cap, and coping matching: measured against your existing profile.
- Drainage correction: so the new base doesn’t repeat the old failure.
- Clean site and documented scope at close: you get a signed written guarantee in hand.
Every price is written before any work begins, and completed work carries our 365-Day Done Right Promise. If it fails within that year, we come back and correct it at no charge.

DIY or Call Us?
You can safely lift a loose cap, read the block name, measure the profile, and take photos of the lean and the drainage line. That’s useful information and it helps us quote accurately. Where DIY goes wrong is the base. Rebuilding compacted base and footing for a block fence is heavy, exacting work, and a block system tipped over is a genuine injury risk to you and anyone nearby. This is also why we don’t hand out step-by-step instructions for setting a fence line. Get the base wrong and the wall fails again within a season or two.
If the fence is already leaning or a course has shifted, leave it alone until a trained crew looks at it. Call (844) 651-3175 and we’ll schedule a free estimate in Denton and write up the scope.
FAQs

How long does a Unilock fence last in Denton? A properly based Unilock block fence should hold well past a decade, and many run considerably longer when the base and drainage are right. In Denton’s clay soils, base and drainage determine lifespan more than the block does. Call (844) 651-3175 for a free assessment of your line.
Can it be repaired instead of replaced? Often, yes. A single shifted section or a run of loose caps can be reset and re-adhered without a full replacement if the base and footing are sound. We’ll tell you honestly whether a repair will hold or whether the base needs rebuilding. Call (844) 651-3175 for a free estimate.
How long does the swap take? A section repair is typically a day or two. A full re-set with new base and original-profile block matching runs longer, and we’ll put the schedule in the written scope before work starts. Call (844) 651-3175 and we’ll quote it.
How do you source the part? We special-order block, caps, and coping matched to the measured profile and dimensions of your existing Unilock system. We don’t claim to stock parts or carry them on a truck. Call (844) 651-3175 and we’ll walk the property and order to match.
Bradford Remodeling Co Denton is an independent contractor and isn’t affiliated with Unilock. We also install and service KraftMaid, Cambria, and Silestone products, along with the premium brands in our documented material roster. Every Denton project gets a written price first and the 365-Day Done Right Promise at close.
When you’re ready to price the job, call (844) 651-3175 for a free estimate. A live person answers around the clock, and we’ll put the full scope and price in writing before any work begins.
Written by the team at Bradford Remodeling Co Denton, serving Denton and nearby areas.












