







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterWhat Cabinet Refacing Costs in Denton, TX - And Why the Number Moves
Cabinet refacing in Denton runs about $4,500 to $9,500 for a standard kitchen - but if your home was built before 1960 near the Courthouse Square, budget $400 to $900 more. Blackland clay movement racks older cabinet boxes off plumb, and veneers won’t sit flush until the frames are shimmed and re-leveled. Most refacing quotes leave that line out until demo day. Bradford Remodeling Co Denton writes it into the price up front, before any work starts. Call (844) 651-3175 for a free estimate that holds.
Here’s what that means for a typical Denton kitchen: you’re not just buying new doors and veneer. You’re buying corrective carpentry on a foundation that has been quietly shifting since the Eisenhower administration.
Key Takeaways
- Refacing saves roughly 40-60% versus full cabinet replacement when your boxes are solid and square.
- Pre-1960 pier-and-beam homes near the Square often need $400-$900 in frame prep that online estimates skip.
- Three real cost components: veneer material, door/drawer replacement, and frame-prep labor.
- The 365-Day Done Right Promise covers adhesion, hinge hardware, and finish integrity for a full year.

The Denton “Out-of-Square Box” Problem Nobody Quotes For
Denton sits on expansive blackland-prairie clay. It swells through wet springs, shrinks hard in July, and does this every year. On pier-and-beam homes ringing the Courthouse Square, the piers move with the soil. Plumb cabinet boxes slowly rack out of square. The doors close crooked, the faces gap, and the reveal along a drawer front drifts by a quarter inch over a decade.
Why does that matter for refacing? Because a new veneer is thin. A stock door hangs on a fixed hinge plate. Neither tolerates a box that’s raked out of level. To make a refaced face sit flush and stay flush, a crew has to shim the frame, re-level the cabinet run, and true up the hinge points first. In a 1940s Craftsman off Oak Street, that’s a real labor line - usually 6 to 14 hours across a full kitchen. It’s the difference between a reface that looks factory and one that shows every crooked box underneath.
Bradford Remodeling includes a frame-square assessment at the estimate, so that number is already in your written price. It does not appear later as a change order.
Three Cost Components, Broke Out Honestly
The national average for refacing is $4,500 to $9,500, and the trade has three cost buckets. Most quotes only show you the first two.
1. Veneer or Thermafoil Material
This is the laminate or wood skin that covers the face frame and cabinet sides. Rigid thermofoil runs cheaper; real wood veneer in oak, maple, or cherry costs more and takes a stain better. Materials alone typically land $1,200 to $3,200 for a full kitchen, depending on coverage and finish.
2. Door and Drawer Replacement
This is where brand spec matters most. Stock box-store doors are usually particleboard core with a paper-thin thermofoil wrap - and they often don’t match the hinge spec a proper reface requires. Bradford works from a documented roster that includes KraftMaid and Wellborn cabinetry, so doors arrive with real wood or plywood construction, manufacturer warranties, and hardware that lines up with the hinge plate on your existing box. A KraftMaid or Wellborn door set typically adds $1,800 to $4,500 for a full kitchen. Store-brand doors can knock $600 to $1,200 off - at the cost of a finish that’s likely to chip at the corner within a few summers of Denton heat.
3. Frame-Prep Labor
This is the invisible one. It covers the shim-and-level work described above, hinge plate relocation, and prep sanding. On square boxes in a newer subdivision, this may be as little as 2 hours. On a pre-1960 home near the Square, it can be a full day or more.

What Refacing Actually Costs in Denton
Here are real ranges for a standard Denton kitchen, broken out by line item. A whole-kitchen refacing job typically falls between $4,500 and $9,500, with pre-1960 homes trending toward the upper end.
| Line Item | Price Range (Denton) |
|---|---|
| Cabinet refacing (standard kitchen) | $4,500 - $9,500 |
| Veneer / Thermafoil material only | $1,200 - $3,200 |
| KraftMaid / Wellborn door & drawer set | $1,800 - $4,500 |
| Frame-prep & corrective shimming (pre-1960) | $400 - $900 |
| Disposal of old doors & drawer fronts | $150 - $400 |
| Crown molding match (if ceiling gap exists) | $300 - $800 |
| Full cabinet replacement (for comparison) | $9,000 - $20,000 |
For a fuller picture of what a kitchen project runs when refacing isn’t the right fit, our Kitchen Remodeling in Denton page lays out the whole-kitchen range of $14,000 to $45,000. And if you’re weighing refacing against replacement outright, our Kitchen Remodeling guide goes deeper on scope and scheduling.
Reface or Replace? The Decision Rule
Refacing makes financial sense when three things are true:
- Your cabinet boxes are square and solid - no rot at the toe kick, no sagging shelves, no cracked face frames.
- Your boxes are plywood or solid wood construction, not particleboard that has swollen from a past leak.
- Your layout works - you’re happy with where the sink, range, and fridge sit.
If any of those fail, replacement wins. A box that’s been racked hard by clay movement and swollen at the toe kick isn’t a refacing candidate. Trying to veneer over a failing box costs more in callbacks than a new cabinet run. Bradford will tell you plainly at the estimate which one you’re looking at.
What Bradford’s Written Price Includes
Every Bradford job starts with a written price before a single tool comes out. That price is itemized, and it doesn’t move at the door. For refacing in Denton, the written scope includes:
- A frame-square assessment during the estimate - so corrective shimming is priced in, not billed later
- Material specification by brand and product line (KraftMaid, Wellborn, or a specified alternative)
- Disposal of old doors and drawer fronts
- Crown molding scope - whether we’re matching existing molding or leaving the ceiling reveal as designed
- The 365-Day Done Right Promise: if a veneer lifts, a hinge fails, or a finish flakes within the full year after completion, we return and correct it at no charge
Technicians are background-checked and uniformed, and a live person answers our phone 24/7 - not a callback queue. Our technicians carry up to 22 years of experience, and the same discipline runs through every Bradford project, from the exterior work that handles Denton’s hail season to interior finish work like bathroom remodeling.
The Two Variables Buyers Almost Never See Quoted
Two lines show up at the end of a job that most refacing quotes leave out entirely.
The first is disposal of old doors and drawer fronts. A full kitchen’s worth of old cabinet doors doesn’t fit in a standard dumpster load, and hauling them off runs $150 to $400 depending on volume. It’s not glamorous, but it’s real money at close.
The second is crown molding. If your existing cabinets have crown molding at the ceiling and you’re keeping the top rail, the new veneer and doors need a matching crown to sit flush. Skipping it leaves a visible gap line at the ceiling. Matching runs $300 to $800 depending on profile and length of run.
FAQs
Cabinet refacing in Denton runs about $4,500 to $9,500 for a standard kitchen, with pre-1960 homes near the Courthouse Square trending $400 to $900 higher due to corrective frame shimming. Call (844) 651-3175 for an exact written quote - the estimate is free and the price is fixed before work starts.
Refacing costs roughly 40-60% less than full cabinet replacement, which runs $9,000 to $20,000 in Denton. Refacing wins when your boxes are square, solid, and plywood or solid wood - replacement is the smarter spend when boxes are swollen, rotted, or racked out of true. A frame-square assessment at the estimate tells you which side of that line you’re on.
Yes, in most cases we can schedule a same-week estimate, and a live person answers our phone 24/7. Call (844) 651-3175 and we’ll book a walkthrough that includes the frame-square check so the written number reflects your actual kitchen. No surprise lines later.
It covers adhesion (veneer lifting or delaminating), hinge hardware failure, and finish integrity for a full year after completion. If any of those fail inside the window, Bradford returns and corrects it at no charge. It’s a written guarantee, handed to you at project close.
Squared Away From the First Estimate
If you’re near the Square or anywhere in Denton dealing with a crooked cabinet run and a quote that keeps changing, get a written number first. Bradford Remodeling Co Denton handles kitchen refacing across Denton with frame-square checks at the estimate, itemized brand-spec pricing, and the 365-Day Done Right Promise in writing. Call (844) 651-3175 for a free estimate today.
Written by the team at Bradford Remodeling Co Denton, serving Denton, TX.
What Our Customers Say
"Straightforward people who do what they say. The crew did what the contract said and called before changing anything."
- Dianne W."Primary bath redo. Tile is straight, shower pan was flood tested, and the vanity fits perfectly."
- Tricia S."Replaced old windows and trim while redoing the kitchen. Clean finish work."
- Ron F.












